Allied Telesis AT-IFS802SPOE manual Igmp Configuration, COS Configuration, TOS Configuration

Page 66

62

AT-IFS802SP/POE(W)-80 User Manual

 

 

6.21.3 COS Configuration

Set up the COS priority level.With the drop-down selection item of PriorityType above being selected as COS only/COS first, this control item will then be available to set the queuing policy for each port.

•COS priority: Set up the COS priority level 0~7 - High, Middle, Low, Lowest.

•Click Apply .

6.21.4 TOS Configuration

Set up the TOS priority. With the drop-down selection item of Priority Type above being selected as TOS only/TOS first, this control item will then be available to set the queuing policy for each port.

•TOS priority: The system provides 0~63 TOS priority level. Each level has 4 types of priority—High, Middle, Low, and Lowest. The default value is ‘Lowest’ priority for each level.When the IP packet is received, the system will check the TOS level value in the IP packet that has received. For example, the user sets the TOS level 25 as high, the system will check the TOS value of the received IP packet. If the TOS value of received IP packet is 25 (priority = high), and then the packet priority will have highest priority.

•Click Apply to have the configuration take effect..

6.22IGMP Configuration

The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries, report packets, and manage IP multicast traffic through the switch. IGMP have three fundamental types of message shown as follows:

 

 

 

 

 

Message

Description

 

 

 

 

 

 

Query

A message sent from the querier (IGMP router or switch) asking for a response

 

 

from each host belonging to the multicast group.

 

 

 

 

 

 

 

 

 

Report

A message sent by a host to the querier to indicate that the host wants to be or

 

 

is a member of a given group indicated in the report message.

 

 

 

 

 

Leave Group

A message sent by a host to the querier to indicate that the host has quit being a

 

 

member of a specific multicast group.

 

 

 

 

 

 

 

 

Page 65 Page 67
Image 66
Page 65 Page 67
Contents AT-IFS802SP/POE Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3100 Hardware Features IntroductionCSMA/CD Software Features EMIPackage Contents Physical Dimension Hardware DescriptionFront Panel Bottom View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP mini-GBIC combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment Login in the Console Interface CLI ManagementCommands Level ExecAbout Web-based Management System LoginWeb-Based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Power over Ethernet Power Limit From Check it to decide the power limit method Factory Default Save ConfigurationSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic RJ-45 Pin Assignments of POE TX+/VCC+ TX-/VCC+Appendix B-Command Sets System Commands SetHigh IP PasswordLow IP Subnet maskDuplex full half Port Commands SetPortid 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Seconds Spanning Tree Commands Set~61440 Time secondsPort Priority AutoTrueFalseTrueFalse QOS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Multicast Filtering Commands SetLldp Commands Set IP-AddrSnmp Commands Set View Name ExcludedIncludedHost-address Port Mirroring Commands Set RXTXBothWords 802.1x Commands SetPort ID SecDisable reject Accept authorizeTftp Commands Set SystemLog, Smtp and Event Commands Set Fault Relay Alarm Commands Set EnabledisableMinute Sntp Commands SetStart time End time TimezoneRing Commands Set Control PortDual Homing Port PoE Commands Set Legacy EnableDisable Port PortNumbersPort PortNumbers

AT-IFS802SPOE specifications

The Allied Telesis AT-IFS802SPOE is a robust and versatile solution designed for modern networking demands, particularly for enterprises requiring reliable connectivity in rugged environments. This device is part of Allied Telesis' commitment to delivering high-quality networking products with superior performance, making it an ideal choice for a range of applications.

One of the standout features of the AT-IFS802SPOE is its Power over Ethernet (PoE) capability. This allows the switch to deliver power directly through the Ethernet cable to connected devices such as IP cameras, VoIP phones, or wireless access points. With a total power budget supporting PoE+, the AT-IFS802SPOE simplifies installations by reducing the need for additional power sources, enhancing flexibility in system design while ensuring a clutter-free environment.

The AT-IFS802SPOE is designed with eight 10/100/1000 Mbps ports, offering extensive connectivity options for various devices. These Gigabit Ethernet ports ensure high-speed data transmission, significantly boosting network efficiency. The switch also supports auto-negotiation, allowing for dynamic adjustment of the speed and duplex settings for each connection. This adaptability contributes to seamless integration within diverse network environments.

In addition, the AT-IFS802SPOE features advanced management capabilities. With support for Layer 2 switching, VLAN (Virtual Local Area Network) configurations, and QoS (Quality of Service) functionalities, users can effectively manage traffic and prioritize critical applications. This characteristic is essential for organizations looking to optimize network performance and ensure that real-time applications such as video conferencing maintain high quality.

The switch is designed with durability in mind, featuring fanless operation for silent performance and a rugged form factor suitable for deployment in various environments, including industrial settings. Its compact size allows for easy installation in tight spaces, while the optional DIN rail mount makes it versatile for mounting in different configurations.

Moreover, Allied Telesis ensures that the AT-IFS802SPOE incorporates advanced security features to protect against unauthorized access and harmful attacks. With features such as MAC address filtering and port security, organizations can maintain network integrity while safeguarding their sensitive data.

In summary, the Allied Telesis AT-IFS802SPOE is a feature-rich, reliable switch that meets the challenges of contemporary networking. With its PoE capability, extensive port options, advanced management features, and rugged design, it is well-suited for any organization seeking to enhance their network infrastructure. Whether deployed in a small office or a complex industrial environment, the AT-IFS802SPOE delivers exceptional performance and reliability, making it an ideal choice for a wide range of networking needs.
Top Page Image Contents