Linksys EF1324 manual Serial Port Configuration, Snmp Configuration

Page 15

Instant EtherFast® Series

Serial Port Configuration

The Serial Port Configuration screen allows you to access the communication parameters for the Switch’s serial port. (Linksys recommends that you do not change the default settings.)

•Baud Rate - The rate at which data is sent between devices. Default is 19200. Options are 9600, 19200, and 38400 baud.

•Data Bits - Sets the data bits of the RS-232 port. Options are 7 and 8.

•Stop Bits - Sets the stop bits of the RS-232 port. Options are 1 and 2.

•Parity - Sets the parity of the RS-232 port. Default is None. Options are none, odd, and even.

•Time-Out- If no input is received from the attached device after this inter- val, the current session is automatically closed. Default is 10 minutes. The range is 0 to 100 minutes, where 0 indicates disabled.

•Auto Refresh - Sets the interval before a console session will auto refresh the console information, such as Spanning Tree Information, Port Configuration, Port Statistics, and RMON Statistics. Default is 1 second. The range is 0, or 5 to 255 seconds, where 0 indicates disabled.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch

SNMP Configuration

The SNMP Configuration screen displays parameters for the Simple Network Management Protocol (SNMP).

•Send Authentication Fail Traps - Issue a trap message to specified IP trap managers whenever authentication of an SNMP request fails. Default is enabled.

•SNMP Communities - Assigns SNMP access based on specified strings.

•IP Trap Managers - Specifies management stations that will receive authen- tication failure messages or other trap messages from the Switch.

Select OK to return to the previous panel.

22

23

Image 15

Contents User Guide Copyright & Trademarks Table of Contents Introduction LEDs Getting to Know the SwitchGigabit Ports Installing the SwitchPre-Installation Considerations RJ-45 PortsUplinking the Switch Switch ManagementRack-Mounting the Switch Powering on the SwitchWeb Management Telnet Management Connecting the Serial Cable to the Switch and ComputerMain Menu Configuring the Switch Using the Console InterfaceLogging On to the Switch OverviewSystem Information System Information MenuManagement Setup Menu Switch InformationIP Configuration Network ConfigurationIP Connectivity Test Ping Http ConfigurationSnmp Configuration Serial Port ConfigurationIP Trap Managers Snmp CommunitiesAdd User User ConfigurationTftp Download Configuration FileDevice Control Menu Management Access ControlSystem Mode Layer 2 Menu Port ConfigurationPort Trunking Configuration Mirror Port ConfigurationStatic Unicast Address Configuration Add Static Address EntryApply Add Multicast Address Entry Static Multicast Address ConfigurationBridge Menu Bridge ConfigurationVlan Menu Spanning Tree Port ConfigurationVlan and Priority Vlan Port ConfigurationIP Menu Vlan Table ConfigurationModify Subnet Subnet ConfigurationSubnet Configuration Modify Ospf Configuration Subnet Configuration Modify RIP ConfigurationSubnet Configuration Modify Dvmrp Configuration Add Subnet Protocol ConfigurationRIP Configuration ARP ConfigurationOspf Configuration Menu Ospf Area Configuration Add Ospf Area IP Menu Ospf Area ConfigurationAdd Ospf Range Ospf Area Range ConfigurationAdd Ospf Virtual Link Ospf Virtual Link ConfigurationAdd Ospf Host Route Ospf Host Route ConfigurationBootp Relay Database Configuration Add Bootp Relay ServerIgmp Snooping Configuration Add Static ARP Entry Static ARP TableAdd Routing Entry Static Route TableSecurity Menu Default Route MenuMAC Filtering Configuration Security ModeAdd MAC Address Filter IP Security Filtering Configuration Igmp Snooping ConfigurationAdd IP Address Filter Port Statistics/Statistics Menu Network Monitor MenuPort Statistics InterfacesEthernet Rmon Statistics Layer 2 Address Table Spanning Tree Bridge Information Spanning Tree Port Information Vlan Dynamic Registration Information Vlan InformationIP Multicast Registration Table Vlan Forwarding InformationSubnet Information Routing Table ARP TableIgmp Cache Multicast Table MenuMulticast Forwarding Cache Dvmrp Neighbor Table Dvmrp Routing TableOspf Interface Table Ospf Table MenuOspf Neighbor Table Ospf Link State TableSystem Restart Menu Ospf Virtual Neighbor TableTroubleshooting Common Problems and SolutionsExit Your firmware has now been updated AppendixUpgrading Firmware via the Serial Port Glossary 121 123 Environmental SpecificationsSales Information Warranty InformationTechnical Support RMA Issues Fax Contact InformationT p / / w w w. l i n k s y s . c o m