Linksys EF1324 manual Subnet Configuration, Modify Subnet

Page 29

Instant EtherFast® Series

Subnet Configuration

The Subnet Configuration screen allows you to specify an IP interface for any VLAN configured on this Switch that needs to communicate with a device outside of its own group (that is, another network segment).

EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch

Modify Subnet

The Modify Subnet screen allows you to modify an IP interface.

•IP Address - The IP address associated with the specified VLAN interface. By convention, the last three digits should be set to “254” to readily distin- guish this device as a router port. To modify this IP interface, select it and press Enter.

•Subnet Mask - A template that identifies the address bits in the host address used for routing to specific subnets. Each bit that corresponds to a “1” is part of the network/subnet number, and each bit that corresponds to “0” is part of the host number.

•VLAN - The VLAN associated with this IP interface.

•RIP - Routing Information Protocol for unicast routing.

•OSPF - Open Shortest Path First routing protocol.

•DVMRP - Distance-Vector Multicast Routing Protocol.

•Status - Status of the VLAN IP.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add an IP interface.

•VLAN - The VLAN associated with this IP interface.

•Select - Use this option to create or modify a VLAN.

•IP Address - The IP address associated with the specified VLAN interface.

•Subnet Mask - A template that identifies the address bits in the host address used for routing to specific subnets.

•Proxy ARP - Enable or disable the Proxy Address Resolution Protocol.

•RIP - Enable or disable the Routing Information Protocol for unicast routing. Select Advanced to make more changes.

•OSPF - Enable or disable the Open Shortest Path First protocol. Select Advanced to make more changes.

•DVMRP - Enable or disable the Distance-Vector Multicast Routing Protocol. Select Advanced to make more changes.

Select Delete to delete a subnet. Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

50

51

Image 29

Contents User Guide Copyright & Trademarks Table of Contents Introduction LEDs Getting to Know the SwitchPre-Installation Considerations Installing the SwitchRJ-45 Ports Gigabit PortsRack-Mounting the Switch Switch ManagementPowering on the Switch Uplinking the SwitchWeb Management Telnet Management Connecting the Serial Cable to the Switch and ComputerLogging On to the Switch Configuring the Switch Using the Console InterfaceOverview Main MenuSystem Information System Information MenuManagement Setup Menu Switch InformationIP Configuration Network ConfigurationIP Connectivity Test Ping Http ConfigurationSnmp Configuration Serial Port ConfigurationIP Trap Managers Snmp CommunitiesAdd User User ConfigurationTftp Download Configuration FileDevice Control Menu Management Access ControlSystem Mode Layer 2 Menu Port ConfigurationPort Trunking Configuration Mirror Port ConfigurationApply Static Unicast Address ConfigurationAdd Static Address Entry Add Multicast Address Entry Static Multicast Address ConfigurationBridge Menu Bridge ConfigurationVlan Menu Spanning Tree Port ConfigurationVlan and Priority Vlan Port ConfigurationIP Menu Vlan Table ConfigurationModify Subnet Subnet ConfigurationSubnet Configuration Modify Ospf Configuration Subnet Configuration Modify RIP ConfigurationSubnet Configuration Modify Dvmrp Configuration Add Subnet Protocol ConfigurationRIP Configuration ARP ConfigurationOspf Configuration Menu Ospf Area Configuration Add Ospf Area IP Menu Ospf Area ConfigurationAdd Ospf Range Ospf Area Range ConfigurationAdd Ospf Virtual Link Ospf Virtual Link ConfigurationAdd Ospf Host Route Ospf Host Route ConfigurationIgmp Snooping Configuration Bootp Relay Database ConfigurationAdd Bootp Relay Server Add Static ARP Entry Static ARP TableAdd Routing Entry Static Route TableSecurity Menu Default Route MenuAdd MAC Address Filter MAC Filtering ConfigurationSecurity Mode Add IP Address Filter IP Security Filtering ConfigurationIgmp Snooping Configuration Port Statistics/Statistics Menu Network Monitor MenuEthernet Port StatisticsInterfaces Rmon Statistics Layer 2 Address Table Spanning Tree Bridge Information Spanning Tree Port Information Vlan Dynamic Registration Information Vlan InformationIP Multicast Registration Table Vlan Forwarding InformationSubnet Information Routing Table ARP TableIgmp Cache Multicast Table MenuMulticast Forwarding Cache Dvmrp Neighbor Table Dvmrp Routing TableOspf Interface Table Ospf Table MenuOspf Neighbor Table Ospf Link State TableSystem Restart Menu Ospf Virtual Neighbor TableExit TroubleshootingCommon Problems and Solutions Upgrading Firmware via the Serial Port Your firmware has now been updatedAppendix Glossary 121 123 Environmental SpecificationsTechnical Support RMA Issues Fax Warranty InformationContact Information Sales InformationT p / / w w w. l i n k s y s . c o m