Adaptec SBC-599, SBC-596 manual Introduction, Features

Page 12

Introduction

The SBC-596/599 is a full-size CPU card. This card uses a Pentium processor based CPU and accommodates up to 256 MB DRAM. It also provides a secondary level 512 KB cache, 2 USB(Universal Serial Bus) ports and 63-level watchdog timer with jumperless setup.

The SBC-596/599 offers power management features to minimize power consumption. It complies with the “Green Function” standard and supports three power saving features: doze, sleep, and suspended mode.

The SBC-599 provides a PCI Ultra Wide SCSI controller with max data transfer rate at 40 MB/sec. In addition, the SBC-599 is equipped with a ISA high drive at 64 mA, a C&T 65550 chipset and a 10Base-T networking controller, which makes the SBC- 599 a highly reliable CPU card perfect for IPC applications or computer telephony integration application.

Features

Pentium up to 233 MHz, P54C, P55C (MMX), Cyrix 6x86, 6x86MX AMD K5, K6 processor

Supports DoubleSpeed SCSI operation up to 40 MB/sec

CPU overheat protection

Flash BIOS, easy to update

On-board VGA CRT/LCD (SBC-599 only)

On-board 10Base-T networking controller (SBC-599 only)

On-board PCI Ultra Wide SCSI controller (SBC-599 only)

16C550 UARTs, two RS-232 ports

Enhanced parallel port, supports SPP/EPP/ECP

PS/2 mouse interface

USB interface

ISA High drive 64mA (SBC-599 only)

63-level watchdog timer, jumperless setup

Power management green function supported, APM 1.1 compliant

2

SBC-596/599 User's Manual

Image 12
Contents SBC-596/599 Copyright Notice AcknowledgementsPage SBC-596/599 series comparison table Packing list Contents Chapter Software Configuration Chapter Award Bios Setup Scsi Setup and Configuration Appendix a Programming the Watchdog Timer General Information Features IntroductionSpecifications Standard PC systemMechanical and environmental Board layout and dimensions Page Installation Guide Jumpers Connectors Locating jumpers Locating connectors Setting jumpers Open ClosedCPU installation and upgrading Install a CPU in the ZIF socketVoltage Select J1, J2, J3, and J4 Frequency Ratio J5 Mtxc CLK Setting/P55C Enabled J7 Clock Setting J8Battery Select and Clear Cmos J9 Scsi Select J10 SBC-599 onlyISA Timing J11 SBC-599 only Dual Power Select J15 LCD/EL Select J13Installing Dram SIMMs Installing SIMMsFront panel connectors CN1,CN2,CN3,CN4 Speaker connector CN1Fan power supply connector CN5 Scsi connectors CN6, CN7 SBC-599 onlyIDE hard drive connector CN8, CN9 Connecting the hard driveFloppy connector CN10 Connecting the floppy drive CRT connector CN16 Flat panel connector CN11LCD power select J12 VGA interface connections SBC-599 onlyKeyboard connectors CN12, CN19 COM-port connectors CN13, CN17 Printer port connector CN14IR connector CN15 USB connectors CN18, CN20 Ethernet connector UTP1, SBC-599 onlyWatchdog timer configurationon Watchdog select J14Software Configuration Utility with VGA Bios SBC-599 only Utility with IDE Bus Master DriverSystem Bios which supports CRT only VGA display software configuration SBC-599 only Connections for four standard LCDs SBC-599 only Pin Pin nameConnections to Planar EL 640 x 480 AD4 EL Pin Pin nameConnections to Toshiba LTM10C042 640 x 480 TFT Color LCD Connections to Sharp LM64C142 640 x 480 Dstn Color LCD Ethernet software configuration SBC-599 only Page Award Bios Setup System configuration verification System test and initializationEntering setup Load DefaultsStandard Cmos Setup Bios Features Setup Chipset Features Setup Power Management Setup PnP/PCI Configuration Integrated Peripherals Load Bios defaults User Password Save & exit setup Exit without savingPCI Svga Setup SBC-599 only Before you begin Installation Simultaneous display modeSleep mode Driver installationWindows setup Changing Color Schemes Windows 95 Drivers Setup Proce- dure Windows NT Drivers Setup Procedure StepOS/2 Drivers Setup Procedure Installing from DiskettePreliminary Steps Page Selecting Screen Resolution/Refresh Rate Selecting Monitor TypeInstallation Notes Scsi Setup and Configurations SBC-599 only Installation and Setup Scsi Configuration GuidelinesScsi ID Numbers Scsi Terminators Termination Termination Installing Scsi Devices Connecting Internal Scsi DevicesConfiguring the Scsi Adapter Page Basic Host Adapter Settings Basic Host Adaptec Settings DefaultBoot Device Settings Scsi Device SettingsSome older SCSI-1 devices do not support Sync Page Advanced Host Adapter Settings Host adapter Bios is enabledPage Using SCSISelect Menus Using the Scsi Disk Utilities Installing Device Drivers Quick Start Instructions Windows 95 or Windows NTTroubleshooting Tips Scsi Device Troubleshooting Windows 95 / Windows NT Troubleshoot- ingPage My CD-ROM drive doesn’ t work properly under Windows Page Information for DOS/Windows 3.1x Users DOS and Windows 3.1x Device DriversDOS and Windows 3.1x Aspi Managers DOS Formatting Utilities Formatter and Partitioner afdisk Page Scsi Setup and Configurations Page Programming the Watchdog Timer REM Watchdog timer example program Pin Assignments Speaker connector CN1 HDD LED connector CN2Reset connector CN3 Power LED/keyboard lock connector CN4 Fan power connector CN5Wide Scsi connector CN6 Pin FunctionPin Function Scsi connector CN7 IDE hard drive connectors CN8, CN9 Pin SignalFloppy connector CN10 Pin Signal PinEnavee GND External keyboard connector CN12 COM port connectors CN13 COM2, CN17 COM1 Printer port connector CN14 IR connector CN15 USB connectors CN18, CN20 Keyboard and PS/2 mouse connector CN19Ethernet 10BASE-T connector UPT1 108 IRQ Default Settings IRQ Default Settings