Parker Hannifin PA Series manual Resolving Problems when Starting Up

Page 48

Chapter 4: Maintaining the PowerStation

Resolving Problems

Resolving Problems when Starting Up

Some of the most common problems that users encounter with PCs occur when they start up their systems. This section describes some problems that may occur in the PA PowerStation during startup and solutions for these problems.

The LED Power indicator on the back of the unit does not light

1Check to see whether the power switch is in the On position, and the PA PowerStation is operating correctly.

a.If the PA PowerStation appears to be operating properly, the LED indicator may be defective. Contact your Parker equipment supplier or Parker Product Technical Support department for assistance.

b.If the PA PowerStation does not appear to be operating properly, restart the PowerStation.

2Check the DC power line to determine whether the DC voltage is either 12VDC or 24VDC.

3Check the power connector to determine whether the leads are properly connected and not reversed. The positive line should connect to the positive terminal, the negative lead should connect to the negative terminal, and the ground lead should connect to the ground terminal.

4Check to see if you have a blown fuse. To replace the fuse, see Replacing the Fuse on page 4-8.

The startup halts with the Award (System Info) screen displayed

1Check for a loose CF card. Restart the PA PowerStation.

The AUTOEXEC.BAT file and/or CONFIG.SYS file does not execute properly

Some startup problems are caused by a corrupted or modified AUTOEXEC.BAT or CONFIG.SYS file. Parker includes backup copies of these files in the \CTC directory on your PowerStation’s CompactFlash Disk and on the PowerStation Start Disk. These files are called AUTOEXEC.CTC and

CONFIG.CTC.

For a complete listing of the AUTOEXEC.BAT and the CONFIG.SYS files, see Appendix B.

If you suspect a problem with either the PA PowerStation’s AUTOEXEC.BAT or CONFIG.SYS files, use the ROM-DOS Copy command to create a backup copy of your current file and overwrite the suspect file with the appropriate backup file. For example, if the AUTOEXEC.BAT file becomes suspect, type the following commands at the ROM-DOS prompt:

copy autoexec.bat autoexec.old copy \ctc\autoexec.ctc autoexec.bat

PA PowerStation User Guide

4-11

Page 47 Page 49
Image 48
Page 47 Page 49
Contents PowerStation Product Warranty Information Copyright and Trademark NoticeSupported Models Table of Contents Maintaining the PowerStation Maintaining the Touchscreen -1 Cleaning the TouchscreenPA PowerStation User Guide Using this Manual IntroductionHardware Versions Downloading Applications and ProjectsDocumentation Library Documentation StandardsText Conventions Style Type of TextCustomer Support Services ISO SymbolsSymbol Meaning Customer SupportProduct Technical Support Technical TrainingGetting Started Selecting a Location Underwriters Laboratories ApprovalTemperature and Humidity Guidelines Field Terminal Wiring RequirementsEnvironmental Guidelines Electrical GuidelinesPA PowerStation User Guide Enclosure Guidelines Radiated Emissions GuidelinesClass I, Division 2 Guidelines Preparing for Installation Creating the CutoutPA Model Cutout Height Cutout Width Installing the PA PowerStation Mounting the PA PowerStationPA PowerStation User Guide Installing an Optional AC Power Supply Preparing a Location for the AC Power SupplyPrepare the Power Supply Mounting Surface Mounting the AC Power SupplyConnecting the Power Supply to the Workstation PowerStation Connectors Serial PortsStarting Your PowerStation Settings and Pinouts for COM1 COM1 Pinouts Pin# Signal1COM2 Dip Switch Settings for 5, 6, 8, and 10 Units Dip Switch Settings and Pinouts for COM2 on 15 Units 4COM2 Dip Switch Settings for 15 Units Transferring Files from a PC to the PA PowerStation RS-485 Directional Control7Serial Transfer Cable Diagram Connecting to a Serial Printer Connecting a PS/2 Mouse on 5, 6, 8, and 10 UnitsConnecting a USB Mouse on 15 Units To Adjust the Mode SettingsSerial Printer Cable Diagram To Print to a Port Configured for Downloading Ethernet Pinouts Pin# SignalEthernet Port Configuring the Ethernet Interface CompactFlashFile Name Description Starting the PowerStation Using the CompactFlash Card Reinstalling the PowerStation UtilitiesRestoring a CompactFlash Card Writing to the CompactFlash CardUsing the Bios Utility Reformating the CompactFlash CardUsing the Bios Utility Entering SetupCleaning the Touchscreen Maintaining the TouchscreenUsing the MachineShop Shell Calibration Utility Calibrating the TouchscreenDisplay Type Model No View Size Contrast Adjustment Steps Model No View SizeReplacing the CompactFlash CompactFlash EjectorPerforming Internal Maintenance Electrostatic Discharge ESD PrecautionsRemoving the PowerStation from an Enclosure Opening the PowerStationClosing the PowerStation Replacing the Fuse Fuse Location PA5 PA10 on left, PA15 on rightAC Power Supply Optional ComponentsResolving Problems General Problem Specific IssueResolving Problems when Starting Up LED Power indicator on the back of the unit does not lightStartup halts with the Award System Info screen displayed Resolving Problems with the Touchscreen Resolving Problems after Start Up Display appears to be blank or very dimPS/2 mouse doesn’t work 5, 6, 8, and 10 units only Keyboard doesn’t work 5, 6, 8, and 10 units onlyAccessing the PowerStation Utilities Ordering Replacement ComponentsUSB keyboard or mouse doesn’t work 15 only Ethernet port doesn’t workComponent Description Powerstation Specifications Physical Specifications CPUDisplay Specifications Table A-4 PA08S & PA08T Display SpecificationsProperty PA08S Description PA08T Description Left/Right 50o/50o 65o/65o Up/Down 30o/50o 65o/55o Environmental Specifications Table A-7 Environmental Specifications Chart CategoryElectrical Specifications Table A-8 Electrical Specifications Chart Category UnitsTesting Specifications Table A-9 European Community Specifications TestTable A-10 Mechanical Testing Specifications Faceplate Chemical Resistance MEKSystem Configuration Files System Configuration Files CONFIG.SYS FileTable B-1 Autoexec.bat Command Line Parameters Description AUTOEXEC.BAT FileCommand Line Parameters Description \STARTUP CD \STARTUP If Exist \STARTUP\AUTOEXEC.BAT CallCD \NET REM Call C\NET\NET.BAT Echo END

PA Series specifications

Parker Hannifin, a global leader in motion and control technologies, has developed the PA Series, a line of advanced linear actuators designed to enhance industrial automation and machinery with reliable performance and integration capabilities. These actuators are engineered for precision, offering a range of features that cater to diverse applications in various sectors, including automotive, aerospace, and manufacturing.

One of the main features of the PA Series is its compact design, which allows for flexible installation even in limited spaces. The actuators are available in various sizes and configurations, enabling engineers to choose the most suitable option for their specific requirements. This versatility in design contributes to efficient operations, as the PA Series can be easily integrated into existing systems or used in new machinery.

The technology behind the PA Series is noteworthy for its robust construction and high durability. These actuators are built with high-quality materials that ensure long service life, even in demanding environments. They are designed to withstand mechanical stress, temperature fluctuations, and exposure to contaminants, making them ideal for use in harsh industrial conditions.

In addition to their strength, the PA Series actuators incorporate advanced motion control technologies. This includes closed-loop systems that ensure accurate positioning and repeatability. With integrated feedback mechanisms such as encoders, the actuators can provide real-time data on position and speed, allowing for precise control and adjustments during operation.

Another significant characteristic of the PA Series is its energy efficiency. The actuators are designed to minimize power consumption while maximizing output performance. This not only reduces operational costs but also supports sustainable practices in industrial operations.

Furthermore, the PA Series features a user-friendly interface for easy programming and control. This accessibility allows engineers and technicians to quickly set up and modify actuator parameters according to specific project demands. As industries continue to evolve towards automation, the flexibility and scalability of the PA Series make it an ideal choice for companies looking to enhance their productivity and efficiency.

Overall, the Parker Hannifin PA Series stands out for its innovative design, superior technology, and reliable performance. Whether deployed in robotics, assembly lines, or material handling applications, these actuators are engineered to meet the rigorous demands of modern industrial automation.
Top Page Image Contents