RuggedCom RX1501 manual Power Supply Wiring and Grounding, Connectors for HI and HIP Power Modules

Page 22

3. Installation

3.2. Power Supply Wiring and Grounding

The RX1501 supports a single power supply, power module 1 (PM1). Power connections are located on the PM1 module face plate. An optional chassis ground connection is located on the front panel as shown in Figure 2.2, “Front View - RX1501”.

RX1501 products can be equipped with either a Phillips Screw Terminal Block or a Phoenix Plug Terminal Block. The Phillips Screw Terminal Block has Phillips screws with compression plates, allowing either bare wire connections or crimped terminal lugs. We recommend the use of #6 size ring lugs to ensure secure, reliable connections under severe shock or vibration. Both terminal blocks have a safety cover, secured with two Phillips screws, which must be removed to make connections. The safety cover must be re-attached after wiring to ensure personnel safety.

For AC and DC power supply wiring examples, refer to Section 3.2.4, “AC Power Supply Wiring Example” and Section 3.2.5, “DC Power Supply WiringExample ”.

The RX1501 has one (1) power supply installed. Service personnel must isolate all power supplies prior to servicing.

3.2.1. Connectors for HI and HIP Power Modules

Figure 3.8. Screw Terminal Power

Figure 3.9. Pluggable Phoenix Power

Connector for HI Power Module

Connector for HIP Power Module

3.2.2. Connectors for 24, 24P, 48, and 48P Power Modules

Figure 3.10. Screw Terminal Power

Figure 3.11. Pluggable Phoenix Power

Connector for 24 and 48 Power Modules

Connector for 24P and 48P Power Modules

RuggedCom® RuggedBackbone™

22

RX1501 Installation Guide Rev 104

Image 22
Contents RuggedBackbone RX1501 Disclaimer Of Liability Warranty Contacting RuggedComAll Rights Reserved Registered TrademarksTable of Contents Page List of Figures Page List of Tables FCC Statement And Cautions Product Overview Feature HighlightsFunctional Overview WAN Universal Power Supply Options RuggedBackbone Modules LM1 through LM6Purpose Description Front PanelModule Status LEDs PM1Ethernet Copper Line Modules LMEthernet Fiber Serial SFP ModularWAN Cellular ModemDDS Digital Data Services APE Appplication Processing EnginePower Supply 27. Pluggable terminal block power module HIP module shownRack Mounting Dimensions InstallationRack Mounting RX1501Rack Mounting Dimensions Top View Installing Panel and DIN Rail Mounting Brackets Panel and DIN Rail MountingPanel and DIN Rail Mounting Dimensions Panel and DIN Rail Mounting DimensionsConnectors for HI and HIP Power Modules Power Supply Wiring and GroundingConnectors for 24, 24P, 48, and 48P Power Modules AC Power Supply Wiring Example Chassis Ground ConnectionCritical Alarm Wiring DC Power Supply Wiring ExampleDB9 Pin Serial Console PortWAN Ports RJ45 T1/E1 pinout1. RJ45 Twisted-Pair Copper Ports WAN Ports BNCCopper Ethernet Ports Gigabit Ethernet 1000Base-TX Cabling RecommendationsTransient Suppression Cabling Category 1000Base Required ActionDDS Ports RJ45 Pin RS232 Mode RS485 Mode RS422 ModeSerial Ports RJ45 RJ45 Pin DescriptionRx LED Color Status SFP Optics Installation, removal, and precautionsDDS Rx and Tx LED Indications Tx LED Color StatusModule Insertion SFP SFP Module RemovalFiber Ethernet Ports 25. SFP module removalCellular Modems Module Order Code DescriptionInstalling SIM Cards for GSM, EDGE, HSPA+ Cellular Modems GSM, EDGE, HSPA+ Cellular Modem CardPage APE Overview Feature DescriptionAPE Application Processing Engine Supported Operating SystemsSecondary Network Interface Placing the APE in a VlanInstalling an Operating System Procedure 3.1. To install an operating systemLED Indicators APE BiosResetting the Module LED Color and StateFAQs Critical Alarm Relay Specifications Technical SpecificationsPower Supply Specifications Copper Ethernet Port SpecificationsCable Tx λ typ Tx min Tx max Distance Power Fiber Ethernet Port SpecificationsFast Ethernet 100Mbps Optical Specifications OrderGigabit Ethernet 1Gbps Optical Specifications Mechanical SpecificationsOperating Environment Test Description Test Levels Severity EMI And Environmental Type TestsESD Ieee 1613 C37.90.x EMI Immunity Type Testsa Test Description Test LevelsAgency Approvals Agency Standards CommentsWarranty RuggedCom Inc