3Com 3 manual Important Safety Information, This must be approved for the country where it is used

Page 58

58APPENDIX A: SAFETY INFORMATION

Important Safety Information

WARNING: Installation and removal of the unit must be carried out by qualified personnel only.

WARNING: If installing the Switch 4200 Family unit in a stack with SuperStack II or SuperStack 3 units that are shallower than the 4200 Family, the Switch 4200 Family unit must be installed below the narrower units.

WARNING: The unit must be earthed (grounded).

WARNING: Connect the unit to an earthed power supply to ensure compliance with safety standards.

WARNING: Power Cord Set:

This must be approved for the country where it is used:

U.S.A. and Canada

United Kingdom only

■The cord set must be UL-approved and CSA certified.

■The minimum specification for the flexible cord is: No. 18 AWG

Type SV or SJ 3-conductor

■The cord set must have a rated current capacity of at least 10A.

■The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration.

■The supply plug must comply with BS1363 (3-pin 13 amp) and be fitted with a 5A fuse which complies with BS1362.

■The mains cord must be <HAR> or <BASEC> marked and be of type H03VVF3GO.75 (minimum).

Europe only:	■ The supply plug must comply with CEE 7/7 (“SCHUKO”).
	■ The mains cord must be <HAR> or <BASEC> marked and
	be of type H03VVF3GO.75 (minimum).
Denmark	■ The supply plug must comply with section 107-2-D1,
	standard DK2-1a or DK2-5a.
Switzerland	■ The supply plug must comply with SEV/ASE 1011.

WARNING: The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet.

Image 58

Contents SuperStack 3Com Corporation 350 Campus Drive Marlborough, MA United States Government LegendContents Setting UP for Management PIN-OUTS Page About this Guide Icon Description ConventionsConvention Description Related DocumentationAbout this Guide Introducing About the Switch FamilySwitch 4200 Family Front View DetailIntroducing the Superstack 3 Switch 4200 Family Port Status LEDs 10/100/1000BASE-T ports Color Indicates Port Status LEDs 10BASE-T/100BASE-TX portsPort Status LEDs SFP ports Unit LEDsRear View Detail LED Color Indicates Power/Self Test LEDAlert LED Rmon Alarm Feature Switch 4200 Family Automatic IP ConfigurationDuplex Mode Quality of Service QoSIntroducing the Superstack 3 Switch 4200 Family Installing the Switch Choosing a Suitable Package ContentsSite Rack-mounting Repeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingTop of Each Other Placing Units OnStacking Units Switch 4200 Family Power-upPowering-up SequenceSFP Operation SFP port on the Switch 4200 28-PortColor State Installing the Switch Correct Cables Your SwitchChoosing TransceiverFiber Cables Cross-over Cable Straight-through CableChoosing the Correct Cables Installing the Switch Setting UP for Management Automatically configured IP information Setting UpConfigure IP information manually for your Switch or view OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesConfiguring the Workstation with IP Information Connecting the Workstation to the SwitchSetting Up the Switch with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Viewing Configured IPAutomatically Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Interface Management Command LineNetwork Using Telnet CLI Management viaInterface Setting Up WebChoosing a Browser Over the Network Setting Up SnmpManagement Protocol Snmp can manage a Switch if Management workstationDefault Users User Default Access Level Name PasswordSecurity device user modify command on the CLI, or Security Device User Modify operation on the web interfaceSetting UP for Management Problem Solving For Technical Support information, see Appendix DPower LED does not light Solving ProblemsSolutions below On powering-up, the Power/Self Test LED lights yellowError message indicating that the SFP transceiver is faulty Solving Communication ProblemsIP Addressing Formation Upgrade ProblemsSolving Stack Solving SoftwareSafety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Información de seguridad importante Schuko Importanti informazioni di sicurezza Avvertenza Lunità deve disporre di messa a terra Prodotto Laser Classe Pin to RS-232 25-pin Null Modem CablePC-AT Serial Cable Pin to 9-pinAssignments Modem CableRJ-45 Pin Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 4200 26-Port 3C17300A Switch 4200 50-Port 3C17302A Switch 4200 28-Port 3C17304A Appendix C Technical Specifications Product ServicesRegister Your PurchaseOnline Access SoftwareTroubleshoot DownloadsContact Us Latin America Telephone Technical Support and Repair Country Telephone NumberUS and Canada Telephone Technical Support and Repair Index NumbersSFP ports 14 SFP transceiver Regulatory Notices

Related manuals

Manual 103 pages 16.51 Kb