3Com 3C16491 manual Montagesatz Anweisungen, Placing Units On Top of Each Other

Page 17

3Insert the two screws supplied in the mounting kit and fully tighten with a suitable screwdriver.

Figure 2 Rack Mounting the Unit

4Repeat steps 2 and 3 for the other side of the unit.

5Insert the unit into the 19-inch rack and secure with suitable screws (not provided).

6Reconnect the cables.

Montagesatz Anweisungen

Der Switch wird mit zwei Halterungen und vier Schrauben geliefert. Diese werde für den Einbau in einen Baugruppenträger benutzt. Bei der Montage der Baugruppe beachten Sie die Anweisungen aus “Positioning the Switch” on page 15.

Rack-Mounting or Free-Standing

17

Der Switch ist eine Baueinheit hoch und passt in einen Standard 19'' (Zoll) Baugruppenträger.

ACHTUNG: Entfernen Sie alle Kabel, bevor Sie fortfahren. Entfernen Sie die selbstklebenden Polster (Füße) von der Unterseite der Baugruppe, falls diese bereits angebracht sind.

1Plazieren Sie die Baugruppe aufrecht auf einer harten, ebenen Fläche mit der Vorderseite zu Ihnen.

2Ordnen Sie eine der Halterungen über den Löchern an der Seite der Baugruppe an.

3Stecken Sie zwei der mitgelieferten Schrauben in die Löcher und drehen Sie diese mit einem geeigneten Schraubendreher fest.

4Widerholen Sie letzten beiden Schritte auf der anderen Seite der Baugruppe.

5Führen Sie die Baugruppe in den 19" (Zoll) Baugruppenträger ein und sichern sie die Baugruppe mit geeigneten Schrauben. (Nicht im Lieferumfang enthalten).

6Schließen Sie alle Kabel wieder an.

Placing Units On Top of Each Other

If the Switch units are free-standing, up to six units can be placed one on top of the other. If you are mixing a variety of Baseline and SuperStack units, the smaller units must be positioned at the top.

Image 17

Contents 3C16491 Baseline Switch PWR Plus3Com Corporation 350 Campus Drive Marlborough MA USA Contents Snmp Regulatory Notices Glossary Index Page Conventions About this GuideProduct Registration Documentation CommentsFeatures and Capabilities Overview of the Baseline SwitchAutosensing of MDI/MDIX Connections Autonegotiating 10/100 Mbps PortsPower-over-Ethernet Capability Physical FeaturesGigabit Combo Ports RJ-45/SFP Front PanelGigabit Combo Ports RJ-45/SFP Link/Activity Status LEDs Rear Panel Power LEDPackage Contents Before You Begin Positioning the SwitchRack-Mounting or Free-Standing Using the Mounting KitPlacing Units On Top of Each Other Montagesatz AnweisungenChecking for Correct Operation Supplying Power to the SwitchInserting an SFP Transceiver Using SFP TranceiversApproved SFP Transceivers Inserting an SFP Transceiver Removing an SFP TransceiverPerforming Spot Checks Installing the Switch Running the Discovery Application Requirements for Accessing the Web InterfaceWelcome screen of Discovery appears Discovered Devices Screen Logging On to the Web InterfaceMenu Navigating the Web InterfaceLists the available items on the menu Menu Item Port Status ButtonsManually Assigned Static IP Address Accessing the Interface Without Using DiscoveryDhcp Assigned IP Address Device Summary Information Configuration OverviewPolling Interval Device ViewModifying the IP Address Settings Administration SettingsAutomatic IP Configuration Color KeyTo set the IP address for the Switch IP SetupRestore Configuration Backup ConfigurationUpgrade Screen Firmware UpgradeInitialize RebootUser Summary System AccessModify User Create UserRemove User System TimeSnmp Add SetupSummary Snmp Remove Configuring VLANsVlan Modify Port Modify VlanModify Port Screen RenameVlan Detail RemovePort Detail Forwarding Tagged/Untagged Frames Sample Vlan ConfigurationsSetting Up Vlan Across Two Switches Setting Up Two VLANs on the Same SwitchSpanning Tree Tagged Vlan ConfigurationSpanning Tree Screen Broadcast Storm Igmp SnoopingIgmp Query PoE Broadcast Storm Setup ScreenAdministration Configuring Port SettingsDetail Port Administration Summary ScreenSpeed/Duplex for 1000 Mbps Connections Port Administration Setup ScreenGuidelines for Creating Trunks Link AggregationLink Aggregation Summary Screen CreateLink Aggregation Modify Screen ModifySpanning Tree per Port Spanning Tree Summary Screen Port Mirroring Spanning Tree Setup ScreenStatistics Port Mirroring Setup ScreenQoS VoIP Summary Screen QoS VoIP Traffic SettingsQoS VoIP Setup Screen Port SetupOUI Add OUI SummaryRadius Client SecurityRadius Client Detail Screen Configure802.1X Summary Screen 802.1X Settings802.1X Detail Screen Address Table MonitoringAddress Table Screen Cable DiagnosticsCable Diagnostic Screen DiagnosticsResetting to Factory Defaults TroubleshootingForgotten Static IP Address Forgotten PasswordSolving LED Issues Link/Activity LED is on, but network performance is poor Fiber cable is connected, but the Module Active LED is offAll ports appear to show continual activity If the Problem PersistsRegister Your Product Purchase Value-Added ServicesTroubleshoot Online Access Software Downloads Contact Us Telephone Technical Support and RepairCountry Telephone Number Latsupportanc@3com.com Environmental Related StandardsPhysical ElectricalAppendix B Technical Information Important Safety Information Safety InformationAppendix C Safety Information Regulatory Notices Page Bandwidth 1000BASE-TAuto-negotiation Category 5 Cables Category 3 CablesCategory 5e Cables Category 6 CablesHalf Duplex Full DuplexIeee 802.1D Ieee 802.1QLink Aggregation LayerMAC Address NetworkServer SwitchSubnet Address Subnet MaskVlan Numbers IndexIndex