3Com 3CR16709-91, 3CR16708-91 manual Inserting a SFP Transceiver

Page 31

SFP Operation 31

Figure 6 Inserting a SFP Transceiver

3.12VDC
5A	MAX

Product label

Wire release lever

Suitable slot on Switch 9 FX

5The 1000BASE-SX or 1000BASE-LX fiber transceiver connects to the network using a duplex LC connector. The 1000BASE-TX transceiver connects to the network using an RJ-45 connector. If you are using a fiber transceiver, attach a male duplex LC connector on the network cable into the duplex LC connector on the transceiver. If using a 1000BASE-TX transceiver, attach an RJ-45 connector on the network cable into the RJ-45 connector on the transceiver.

6Connect the other end of the cable to a device fitted with an appropriate Gigabit Ethernet connection.

7Check the Module Status LED on the front of the Switch to ensure that it is operating correctly. Refer to “LEDs” on page 14 for more information.

Removing an SFP If you wish to remove a 3Com transceiver (it is not necessary to Transceiver power-down your Switch):

1Disconnect the cable from the transceiver.

2Move the wire release lever downwards until it is pointing toward you.

3Pull the wire release lever toward you to release the catch mechanism;

the transceiver will then easily slide out.

Image 31

Contents 3CR16708-91 3CR16709-91 United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USAContents Setting UP for Management Outs Problem SolvingPage About this Guide Icon Description ConventionsConvention Description Documentation RelatedDocumentation Pddtechpubscomments@3com.com CommentsIntroducing Hardware Features Switch Alert LED Power LED Port Status Leds PoE Status Leds Switch Front View Detail100BASE-FX Port Status LEDs Switch 9 FX only SFP Module Status LED Switch 9 FX onlyColor Indicates 10BASE-T/100BASE-TX Port Status LEDs Alert LED LEDSwitch 9 rear view Switch Rear View DetailSwitch Rear View Detail Page Default Settings shows the default settings for the Switch Page Installing the Switch Choosing a Suitable Package ContentsSite Air temperature around the Switch does not exceed 50 C 122 F Instructions for Cement Walls Wall-mountingUpwards MountingMake two holes 150 mm 5.9 in. apart Instructions for Wood WallsColor State Power and Alert LED colorsPower-up Sequence Cross-over Cable Straight-through Cable SFP Operation Installing the Switch Inserting a SFP Transceiver Installing the Switch Setting UP for Management Overview Setting UpConfigure IP information manually for your Switch or view Automatically configured IP informationAutomatic IP Configuration Manual IP ConfigurationSetting UP for Management Pre-requisites Manually Configuring IP InformationConnecting a workstation to the Switch via the console port Connecting the Workstation to the SwitchExample top-level command line interface menu Setting Up the Switch with IP InformationViewing Configured IPAutomatically Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Web Interface Management on Refer to Setting Up Command Line Interface Management onCLI Management via Command LineNetwork Using Telnet Interface ManagementInterface Setting Up WebChoosing a Browser Management workstation Setting Up SnmpManagement Protocol Snmp can manage a Switch if Over the NetworkUser Default Name Password Access Level Default UsersDefault Users and Passwords Setting UP for Management Problem Solving Indicated by LEDs Solving ProblemsRefer to the list of suggested solutions below ProblemsSolving Hardware IP Addressing Solving Communication ProblemsHow do you obtain a registered IP Address? Solving Software Upgrade Problems Problem Solving Safety Information This must be approved for the country where it is used Power Cord Set Japan Important Safety InformationImportant Safety Information Schko ’information de Sécurité Importante’information de Sécurité Importante Vorsicht Europe Wichtige SicherheitsinformationenInformación de seguridad importante Schuko Dispositivo Láser DE Clase CSA Importanti Informazioni di SicurezzaAvvertenza porte a fibre ottiche Protezione degli occhi Appendix a Safety Information Panel. The pinout is shown below RJ-45 Pin Signal DB-9 Pin DirectionRJ-45 to RS-232 Adapter CablePin Number ConnectorsRJ-45 Pin AssignmentsOfficeConnect Managed Switch 9 and Switch 9 FX Standards Supported Protocols Used for AdministrationTerminal Emulation Purchase ServicesRegister Your ProductDownloads Access SoftwareTroubleshoot OnlineContact Us Latin America Telephone Technical Support and Repair Country Telephone NumberUS and Canada Telephone Technical Support and Repair Index Snmp Regulatory Notices