Rosewill EASYN400 Appendix C FCC Interference Statement, FCC Radiation Exposure Statement

Page 110

Wireless RouterRNX-EasyN400

User Manual

 

 

 

 

 

 

Appendix C – FCC Interference Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

zReorient or relocate the receiving antenna.

zIncrease the separation between the equipment and receiver.

zConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

zConsult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Requirements for indoor vs. outdoor operation, license requirements and allowed channels of operation apply in some countries as described below:

. In Italy the end-user must apply for a license from the national spectrum authority to operate this device outdoors.

. In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz band: Channel 13.

. In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band: Channels 1 - 7.

109

Image 110
Contents Wireless Router RNX-EasyN400 Safety Warning Table of Contents 100 Before We Begin Overview Key FeaturesIntroduction Package Contents Product Layout and LED Signal Color Status DescriptionRNX-EasyN400 Placement Network + System RequirementsRNX-EasyN400’s LAN & WAN Cable Connection Setup RNX-EasyN400 LAN Connection Diagram Setup Wizard Setup Wizard Getting StartSetup Wizard Configuration Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Setup Wizard Connect Mode Selection AP Router ModeDhcp Mode Selection Wireless Security Selection Label DescriptionWireless RouterRNX-EasyN400 Ssid AP Repeater Mode Connecting to RNX-EasyN400 in AP Repeater Mode Highlight Internet Protocol TCP/IP and click Properties Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Accessing RNX-EasyN400 through Web Browser in Router Mode Router Mode and Repeater Mode Resetting the RNX-EasyN400Procedure to Use the Reset Button Navigate RNX-EasyN400System Navigating RNX-EasyN400 in AP Router ModeRNX-EasyN400 Side Menu Description Table AP Router Mode Firewall WirelessInternet AdvancedNavigating RNX-EasyN400 in AP Repeater Mode ALGRNX-EasyN400 Side Menu Description Table AP Repeater Mode Please see RNX-EasyN400’s System Status2 LAN LAN IPDhcp Dhcp ServerWireless RouterRNX-EasyN400 Schedule 5 Log MonitorLanguage RNX-EasyN400’s Wizard RNX-EasyN400’s Internet Dynamic IPStatic IP Point-to-Point over Ethernet Protocol PPPoEPoint-to-Point Tunneling Protocol Pptp RNX-EasyN400’s Wireless BasicWireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 WDS with AP Router SettingsSupport mixed mode such as WPA-PSK/WPA2-PSK Mixed mode Advanced Security Enable 802.1x Authentication WEP Encryption WPA Pre-Shared Key Encryption Filter WPA-Radius EncryptionAdding an address into the list Remove an address from the listWPS Wi-Fi Protected Setup Client List PolicyWireless RouterRNX-EasyN400 RNX-EasyN400’s Firewall Demilitarized Zone DMZDenial of Service DoS MAC Filter Add PC MAC AddressIP Filter Remove PC MAC AddressRemove PC IP Address URL FilterAdd PC IP Address Add URL KeywordRemove URL Keyword Port Mapping RNX-EasyN400’s AdvancedNetwork Address Translation NAT Add Port Mapping Remove Port MappingPort Forwarding Virtual Server Port Triggering Special Applications Wireless RouterRNX-EasyN400 Application Layer Gateway ALG Priority Queue Quality of Service QoSUPnP Bandwidth Allocation Routing Admin and Remote Management RNX-EasyN400’s ToolsRemote management Time Synchronize with the NTP serverWireless RouterRNX-EasyN400 Power DdnsDiagnosis FirmwareWireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Reset Back-upWireless RouterRNX-EasyN400 Repeater Mode Highlight Internet Protocol TCP/IP and click Properties Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 RNX-EasyN400 in Repeater Mode’s System Schedule 4 Log Monitor Wireless RouterRNX-EasyN400 RNX-EasyN400 in Repeater Mode’s Wireless RNX-EasyN400 in Repeater Mode’s WizardWireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 PC Network Adapter setup Under Windows XP Wireless RouterRNX-EasyN400 Wireless RouterRNX-EasyN400 Appendix a Product Specification Hardware Feature101 Appendix B Troubleshooting 103 104 105 106 107 108 FCC Radiation Exposure Statement Appendix C FCC Interference StatementFederal Communication Commission Interference Statement Wireless RouterRNX-EasyN400 Appendix D IC Interference Statement Industry Canada statement