Powerware 5115A USB manual Tu r n i n g t h e U P S O n, Tu r n i n g t h e U P S O f f, Operation

Page 15

C H A P T E R 3

OPERATION

This section describes

•Turning the UPS on and off

•Starting the UPS on battery

•Standby mode

•The UPS front panel and LEDs

•Initiating the self-test

Tu r n i n g t h e U P S O n

To turn on the UPS, press the button on the front panel (shown in Figure 7). After

the UPS is turned on, it conducts a self-test and enters Normal mode. The indicator illuminates indicating that power is available from the UPS output receptacles.

Starting the UPS on Battery

To turn on the UPS without using utility power, press and hold the button for two seconds. When the UPS starts on battery, it does not conduct a self-test to conserve battery power.

NOTE The UPS does not auto-detect the input frequency when starting on battery; the default is the last frequency used by the UPS.

Tu r n i n g t h e U P S O f f

To turn off the UPS, press the button on the front panel and then unplug the UPS from the power outlet. If you do not unplug the UPS, it remains in Standby mode.

S ta n d b y M o d e

When the UPS is turned off and remains plugged into a power outlet, the UPS is in

Standby mode. The battery recharges when necessary and the indicator is off, indicating that power is not available from the UPS output receptacles.

Powerware	®	5115A USB User’s Guide • www.powerware.com.au	9

Image 15

Contents Powerware 5115A USB Page User’s Guide Special Symbols Powerware 5115 -Introduction Installation Troubleshooting A P T E R Powerware 5115 Introduction Installation S p e c t i n g t h e E q u i p m e n tF e t y P r e c a u t i o n s S ta l l i n g t h e U P S Typical UPS InstallationPowerware VA Rear Panel S R e a r P a n e l sCommunication Port Powerware 5115A USB User’s Guide Ta n d b y M o d e Starting the UPS on BatteryTu r n i n g t h e U P S O n Tu r n i n g t h e U P S O f fI t i a t i n g t h e S e l f Te s t S F r o n t P a n e lM m u n i c a t i o n P o r t Additional UPS FeaturesCommunication Port Pin Assignment B P o r tNetwork Transient Protector T w o r k Tr a n s i e n t P r o t e c t o rPowerware 5115A USB User’s Guide UPS Maintenance S a n d B a t t e r y C a r eStoring the UPS and Batteries P l a c i n g B a t t e r i e s Powerware UPS Maintenance C y c l i n g t h e U s e d B a t t e r y Te s t i n g N e w B a t t e r i e sPowerware 5115A USB User’s Guide Specifications Weights and DimensionsModel List and Mechanical Electrical Output Environmental and SafetyBattery Run Times in Minutes BatteryPowerware 5115A USB User’s Guide D i b l e Alarm s a n d U P S C o n d i t i o n s TroubleshootingSilencing an Audible Alarm Alarm or Condition Possible Cause Action Indicator Legend Lit Flashing Troubleshooting GuideBeep UPS is running on Every Output voltage is below Call the Powerware National Service and Repair Centre Service and SupportPowerware 5115A USB User’s Guide Warranty Information Warranty Information Within 30 days and receive $50,000 Computer/Load Protection Guarantee Extended Ten-Year Pro-Rated Warranty Claims ProcedureDandenong VIC Australia Standard Warranty Registration Web Site Customer Service Offices