SUPER MICRO Computer user manual P4SCT/P4SCT+/P4SCT+II Quick Reference, Connectors Description

Page 11

 

 

Chapter 1: Introduction

 

P4SCT/P4SCT+/P4SCT+II Quick Reference

Jumpers

Description

Default Setting

J18

Speaker

Pins 3-4 (In.Buzzer)

J33

VGA Enable/Disable

Pins 1-2

(Enabled)

J36

Keylock Header

Open(Disabled)

JBT1

CMOS Clear

See Section 2-7

JP1,JP2

CPU Clock Speed

Pins 1-2 (Auto)

JP8

Watch Dog Reset

Pins 1-2

(WD Reset)

JP20

Power Force On

Open (Disabled)

JPL2 (P4SCT+/SCT+II)

GLAN2

Pins 1-2

(Enabled)

JPS1 (P4SCT+/SCT+II)

Marvell's SATA Enable

Pins 1-2

(Enabled)

JPUSB

USB1/2 Wake Up

Pins 1-2 (VCC5)

JPWAKE

KB Wake Up

Pins 1-2 (VCC5)

Connectors

Description

DIMM0A/0B/1A/1B

Memory (DIMM) Slots (1 through 4)

Fans 1-5

CPU/CH Fan1, CH Fan 2, 3, 4, OH Fan/CH Fan 5

GLAN1/2(GbLAN)

LAN1:J23,J24, LAN2:J25,J26(LAN2:P4SCT+/SCT+II)

J2, J5

IDE Ports (J2: IDE1, J5:IDE2)

J3, J4

Intel's Serial ATA Connectors 1/2

J7

Floppy Disk Drive Connector

J8

Parallel Printer Port

J9,J10

COM1(J9), COM2(J10)

J11

Keyboard/Mouse Connector

J15

System Management Bus

J16

Infrared

 

J17

Power LED

 

J20

ATX Power Connector

J21

+12V Power Connector

J36

Keylock Connector

J37

Intel's SATA LED Header

JF1

Front Control Panel

JG1

VGA Header

 

JL1

Chassis Intrusion Header

JP17

Power LED

 

JS1-4

Marvell's SATA1-8 Connectors (P4SCT+/SCT+II)

JS9

Marvell's SATA1-4 LED Header (P4SCT+/SCT+II)

JX1-3

PCI-X Slots 1-3

 

USB 1/2 (J12,13)

Back Panel Universal Serial Ports 1/2

USB 3/4

Front Panel Universal Serial Ports 3/4

WOL

Wake-On-LAN

 

WOR

Wake-On-Ring Header

1-5

Image 11
Contents Super Manual Revision Rev .0c Date Dec About This Manual Manual Organization PrefaceTable of Contents Table of Contents TroubleshootingAppendices BiosOverview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeSuper P4SCT P4SCT/P4SCT+/P4SCT+II P4SCT/P4SCT+/P4SCT+II Quick Reference Jumpers Description Default SettingConnectors Description MCH PC Health Monitoring Motherboard FeaturesExpansion Slots Other Acpi FeaturesDimensions Onboard I/OMemory Controller Hub MCH Hance Rapids 6300ESB ICH System FeaturesSystem Memory Interface Bit PCI/PCI-X Interface FeaturesSerial Atasata Interface PC Health Monitoring Power Configuration Settings Wake-On-LAN WOR Header Power SupplySuper I/O Static-Sensitive Devices PrecautionsInstallation Procedures Install the battery upside down to avoid possible explosionInstallation of the Processor and Heatsink Processor and Heatsink Fan InstallationPage Mounting the Motherboard in the Chassis Installing DDR MemoryMemory Module Installation See Figure To Remove To InstallSupport Front Control Panel I/O Port/Control Panel Connector LocationsPin PWR Connector B -pin PWR Connector C. PWR On Connector Connecting CablesPower Supply Connectors Pwon ConnectorOverheat LED OH Reset ConnectorReset Button P4SCT+II Only GLAN1 LEDPWR On LED PowerLED ConnectorPWR LED Connector NMI Button Speaker ConnectorIR Connector NMI Button Speaker Connector IR ConnectorCPU/CH Fan OH/CH Fan COM Port Serial PortsFan Headers Chassis Intrusion Chassis IntrusionWake-On-LAN Wake-On-LANVGA Header VGA ConnectorEthernet Ports GLAN1 and GLAN2 *P4SCT/P4SCT+II only SMB HeaderUSB 1/2 ATX PS/2 Keyboard and PS/2 Mouse PortsUniversal Serial Bus USB Keyboard/MouseWake-On-Ring Keylock Enable/DisableWake-On Ring B. Keylock Enable Standby PWR LED Intel Sata LED Marvell Sata LED Standby Power LEDIntels Sata LED Marvells Sata LED *P4SCT+/ P4SCT+II OnlyClear Cmos Jumper SettingsExplanation Jumpers Cmos ClearUSB Wake-Up Marvells Sata Enable *P4SCT+/P4SCT+II OnlyMarvell Sata Enable USB Wake-Up *USB1/2 OnlyWatch Dog Enable Watch Dog Enable/DisableKeyboard Wake-Up GLAN2 Enable/DisableKeyboard Wake-UP Enable Glan EnableCPU Speed VGA Enable/DisableVGA Enable Front Side Bus SpeedParallel Port Parallel Port ConnectorParallel Port, Floppy Drive, Hard Drive and AGP Connections Floppy Floppy ConnectorIDE Connectors IDE 1 ConnectorAGP Slot 5V 8xAGP Pro Slot *P4SCT/P4ST+IIPage No Video Troubleshooting ProceduresBefore Power On No PowerLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Question What type of memory does my motherboard support? Frequently Asked QuestionsQuestion How do I update my BIOS? P4SCT/P4SCT+/P4SCT+II PCI IRQs Question Whats on the CD that came with my motherboard?Returning Merchandise for Service Page Introduction System BiosHow To Change the Configuration Data Starting the Setup UtilityPress DEL to enter Setup Running SetupMain Bios Setup Main Bios Setup MenuLegacy Diskette B Access ModeDate/Time Legacy Diskette aQuiet Boot Advanced Bios SetupAdvanced Bios Features Quick BootAdvanced Chipset Control CSA LAN Giga-LAN ECC ConfigurationSata Mode Serial ATA Port0/1 modeKeyboard Input Clock 3 I/O Device ConfigurationUSB Legacy Support CPU THRM-ThrottlingUse IR Pins Uart Mode SelectIR Transmission Delay UR2 Duplex ModeHot Key Power On PnP ConfigurationPower On Function KB Power On PasswordConsole Redirection Hardware Monitor Agent after BootCPU Warning Temperature Processor & Clock Options Security Set Supervisor PasswordSet User Password Password CheckFirst Boot Device BootCD ROM Drives Boot Priority Hard Disk Boot PriorityExit Discard Changes Load Fail-Safe DefaultsLoad Optimized Defaults Appendix a Bios Post Messages Page Appendix B Award Bios Post Codes Post hex Description Super P4SCT/P4SCT+//P4SCT+II User’s ManualAppendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix C Software Installation Instructions Enhanced Mode ATA Operate ModeCombined Mode Appendix C Software Installation Instructions Using the Array Configuration Utility ACU Using the Adaptec RAID Configuration Utility ARCManaging Arrays RAID 1 only-the following prompt is also displayed From the ARC menu, select Array Configuration Utility ACUViewing Array Properties Deleting ArraysTo create an array Creating ArraysAssigning Array Properties Raid Level Create Via When Appropriate When you are finished, press Done as the screen shown below Deleting a Bootable Array Adding a Bootable ArrayAdding/Deleting Hotspares To initialize drives Initializing Disk DrivesPage Page To Rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesPage You can choose from the following options To Exit Adaptec RAID Configuration UtilityInstalling Intels Hance Rapids Driver by Adaptec and the OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control

P4SCT+, P4SCT, P4SCT+II specifications

SUPER MICRO Computer has established a prominent reputation in the realm of high-performance computing solutions, and its line of motherboards, including the P4SCT+II, P4SCT, and P4SCT+, stands as a testament to their commitment to quality and innovation. These motherboards are designed primarily for Intel Pentium 4 processors, embodying the P4 chipset architecture that enhances reliability and performance in computing tasks.

One of the significant features of the P4SCT+II is its support for dual-channel DDR SDRAM. This allows for increased memory bandwidth, which is crucial for demanding applications requiring rapid data processing. With a maximum memory capacity of 4GB, users can expect consistent performance even under heavy workloads. Moreover, these motherboards come equipped with a variety of PCI slots, including PCI Express, allowing for the addition of high-speed graphics cards, RAID controllers, and other expansion options that cater to specific user needs.

The P4SCT+II distinguishes itself with integrated features like the 10/100 Ethernet controller, which ensures seamless connectivity for networking applications. Additionally, the inclusion of several SATA ports facilitates fast data transfer rates for storage solutions, significantly boosting overall system performance. The motherboards also support IDE drives, ensuring versatility for users who prefer traditional storage solutions.

Power efficiency is another hallmark of SUPER MICRO's designs. The P4SCT+II, P4SCT, and P4SCT+ utilize an advanced power management system, optimizing power consumption without compromising performance. This approach not only enhances the longevity of the components but also contributes to eco-friendly computing practices.

From a thermal management perspective, these motherboards are engineered with robust cooling solutions. They provide ample fan headers and locations for passive heatsinks to maintain optimal operating temperatures. This feature is crucial for users who push their systems to the limit, whether for gaming, multitasking, or running resource-intensive applications.

In summary, the SUPER MICRO Computer P4SCT+II, P4SCT, and P4SCT+ motherboards exemplify a blend of advanced technology and practicality. With support for dual-channel DDR SDRAM, versatile PCI slots, integrated networking capabilities, and efficient power management, they cater to both professional and personal computing environments. These motherboards are ideal for anyone seeking high reliability and performance in their computing endeavors, making them a valuable investment in the world of technology.