SUPER MICRO Computer P4SCT+II Contacting Supermicro, Headquarters, Europe, Asia-Pacific

Page 8

SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual

Contacting Supermicro

Headquarters

Address:	SuperMicro Computer, Inc.
	980 Rock Ave.
	San Jose, CA 95131 U.S.A.
Tel:	+1	(408)	503-8000
Fax:	+1	(408)	503-8008
Email:	marketing@supermicro.com (General Information)
	support@supermicro.com (Technical Support)
Web Site:	www.supermicro.com

Europe

Address:	SuperMicro Computer B.V.
	Het Sterrenbeeld 28, 5215 ML
	's-Hertogenbosch, The Netherlands
Tel:	+31	(0)	73-6400390
Fax:	+31	(0)	73-6416525
Email:	sales@supermicro.nl (General Information)
	support@supermicro.nl (Technical Support)
	rma@supermicro.nl (Customer Support)

Asia-Pacific

Address:	SuperMicro, Taiwan
	4F, No. 232-1 Liancheng Road
	Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel:		+886-(2)	8226-3990
Fax:		+886-(2)	8226-3991
Web Site:		www.supermicro.com.tw
Technical Support:
Email:	support@supermicro.com.tw
Tel:	886-2-8226-3990, ext.132 or 139

1-2

Image 8

Contents Super Manual Revision Rev .0c Date Dec Preface About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificSuper P4SCT P4SCT/P4SCT+/P4SCT+II P4SCT/P4SCT+/P4SCT+II Quick Reference Jumpers Description Default SettingConnectors Description MCH PC Health Monitoring Motherboard FeaturesExpansion Slots Acpi Features DimensionsOnboard I/O OtherMemory Controller Hub MCH Hance Rapids 6300ESB ICH System FeaturesSystem Memory Interface Bit PCI/PCI-X Interface FeaturesSerial Atasata Interface PC Health Monitoring Power Configuration Settings Power Supply Wake-On-LAN WOR HeaderSuper I/O Precautions Installation ProceduresInstall the battery upside down to avoid possible explosion Static-Sensitive DevicesProcessor and Heatsink Fan Installation Installation of the Processor and HeatsinkPage Mounting the Motherboard in the Chassis Installing DDR MemoryMemory Module Installation See Figure To Remove To InstallSupport I/O Port/Control Panel Connector Locations Front Control PanelConnecting Cables Power Supply ConnectorsPwon Connector Pin PWR Connector B -pin PWR Connector C. PWR On ConnectorOverheat LED OH Reset ConnectorReset Button GLAN1 LED P4SCT+II OnlyPWR On LED PowerLED ConnectorPWR LED Connector Speaker Connector IR ConnectorNMI Button Speaker Connector IR Connector NMI ButtonCPU/CH Fan OH/CH Fan COM Port Serial PortsFan Headers Chassis Intrusion Wake-On-LANWake-On-LAN Chassis IntrusionVGA Connector Ethernet Ports GLAN1 and GLAN2 *P4SCT/P4SCT+II onlySMB Header VGA HeaderATX PS/2 Keyboard and PS/2 Mouse Ports Universal Serial Bus USBKeyboard/Mouse USB 1/2Wake-On-Ring Keylock Enable/DisableWake-On Ring B. Keylock Enable Standby Power LED Intels Sata LEDMarvells Sata LED *P4SCT+/ P4SCT+II Only Standby PWR LED Intel Sata LED Marvell Sata LEDJumper Settings Explanation JumpersCmos Clear Clear CmosMarvells Sata Enable *P4SCT+/P4SCT+II Only Marvell Sata EnableUSB Wake-Up *USB1/2 Only USB Wake-UpWatch Dog Enable/Disable Watch Dog EnableGLAN2 Enable/Disable Keyboard Wake-UP EnableGlan Enable Keyboard Wake-UpVGA Enable/Disable VGA EnableFront Side Bus Speed CPU SpeedParallel Port Parallel Port ConnectorParallel Port, Floppy Drive, Hard Drive and AGP Connections Floppy Connector IDE ConnectorsIDE 1 Connector Floppy5V 8xAGP Pro Slot *P4SCT/P4ST+II AGP SlotPage Troubleshooting Procedures Before Power OnNo Power No VideoLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Question What type of memory does my motherboard support? Frequently Asked QuestionsQuestion How do I update my BIOS? Question Whats on the CD that came with my motherboard? P4SCT/P4SCT+/P4SCT+II PCI IRQsReturning Merchandise for Service Page System Bios How To Change the Configuration DataStarting the Setup Utility IntroductionRunning Setup Main Bios SetupMain Bios Setup Menu Press DEL to enter SetupAccess Mode Date/TimeLegacy Diskette a Legacy Diskette BAdvanced Bios Setup Advanced Bios FeaturesQuick Boot Quiet BootAdvanced Chipset Control ECC Configuration Sata ModeSerial ATA Port0/1 mode CSA LAN Giga-LAN3 I/O Device Configuration USB Legacy SupportCPU THRM-Throttling Keyboard Input ClockUart Mode Select IR Transmission DelayUR2 Duplex Mode Use IR PinsPnP Configuration Power On FunctionKB Power On Password Hot Key Power OnConsole Redirection Hardware Monitor Agent after BootCPU Warning Temperature Processor & Clock Options Set Supervisor Password Set User PasswordPassword Check SecurityBoot CD ROM Drives Boot PriorityHard Disk Boot Priority First Boot DeviceExit Discard Changes Load Fail-Safe DefaultsLoad Optimized Defaults Appendix a Bios Post Messages Page Appendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Post hex DescriptionAppendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix C Software Installation Instructions Enhanced Mode ATA Operate ModeCombined Mode Appendix C Software Installation Instructions Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays From the ARC menu, select Array Configuration Utility ACU Viewing Array PropertiesDeleting Arrays RAID 1 only-the following prompt is also displayedCreating Arrays To create an arrayAssigning Array Properties Raid Level Create Via When Appropriate When you are finished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayAdding/Deleting Hotspares Initializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Disk Utilities To access the disk utilitiesPage To Exit Adaptec RAID Configuration Utility You can choose from the following optionsInstalling Intels Hance Rapids Driver by Adaptec and the OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control