SUPER MICRO Computer P4SCT+II user manual Bios, Appendices

Page 6

 

 

Table of Contents

 

 

Chapter 4: BIOS

 

4-1

Introduction

4-1

4-2

Running Setup

4-2

4-3

Main BIOS Setup

4-2

4-4

Advanced BIOS Setup

4-4

 

4-4.1 Advanced BIOS Features

4-4

 

4-4.2 Advanced Chipset Control

4-5

 

4-4.3 I/O Device Configuration

4-7

 

4-4.4 PnP Configuration

4-9

 

4-4.5 Console Redirection

4-10

 

4-4.6 Hardware Monitors

4-11

 

4-4.7 Processor & Clock Options

4-12

4-5

Security

4-13

4-6

Boot

4-14

4-7

Exit

4-15

Appendices:

 

Appendix A: BIOS POST Messages

A - 1

Appendix B: BIOS POST Codes

B-1

Appendix C: Software Installation Instructions

C-1

vi

Image 6
Contents Super Manual Revision Rev .0c Date Dec Preface About This Manual Manual OrganizationTable of Contents Troubleshooting Table of ContentsBios AppendicesChecklist OverviewEurope Contacting SupermicroHeadquarters Asia-PacificSuper P4SCT P4SCT/P4SCT+/P4SCT+II Jumpers Description Default Setting Connectors DescriptionP4SCT/P4SCT+/P4SCT+II Quick Reference MCH Motherboard Features Expansion SlotsPC Health Monitoring Onboard I/O Acpi FeaturesDimensions OtherHance Rapids 6300ESB ICH System Features System Memory InterfaceMemory Controller Hub MCH Features Serial Atasata InterfaceBit PCI/PCI-X Interface PC Health Monitoring Power Configuration Settings Power Supply Wake-On-LAN WOR HeaderSuper I/O Install the battery upside down to avoid possible explosion PrecautionsInstallation Procedures Static-Sensitive DevicesProcessor and Heatsink Fan Installation Installation of the Processor and HeatsinkPage Installing DDR Memory Memory Module Installation See FigureMounting the Motherboard in the Chassis To Install SupportTo Remove I/O Port/Control Panel Connector Locations Front Control PanelPwon Connector Connecting CablesPower Supply Connectors Pin PWR Connector B -pin PWR Connector C. PWR On ConnectorReset Connector Reset ButtonOverheat LED OH GLAN1 LED P4SCT+II OnlyPowerLED Connector PWR LED ConnectorPWR On LED NMI Button Speaker Connector IR Connector Speaker ConnectorIR Connector NMI ButtonSerial Ports Fan HeadersCPU/CH Fan OH/CH Fan COM Port Wake-On-LAN Chassis IntrusionWake-On-LAN Chassis IntrusionSMB Header VGA ConnectorEthernet Ports GLAN1 and GLAN2 *P4SCT/P4SCT+II only VGA HeaderKeyboard/Mouse ATX PS/2 Keyboard and PS/2 Mouse PortsUniversal Serial Bus USB USB 1/2Keylock Enable/Disable Wake-On Ring B. Keylock EnableWake-On-Ring Marvells Sata LED *P4SCT+/ P4SCT+II Only Standby Power LEDIntels Sata LED Standby PWR LED Intel Sata LED Marvell Sata LEDCmos Clear Jumper SettingsExplanation Jumpers Clear CmosUSB Wake-Up *USB1/2 Only Marvells Sata Enable *P4SCT+/P4SCT+II OnlyMarvell Sata Enable USB Wake-UpWatch Dog Enable/Disable Watch Dog EnableGlan Enable GLAN2 Enable/DisableKeyboard Wake-UP Enable Keyboard Wake-UpFront Side Bus Speed VGA Enable/DisableVGA Enable CPU SpeedParallel Port Connector Parallel Port, Floppy Drive, Hard Drive and AGP ConnectionsParallel Port IDE 1 Connector Floppy ConnectorIDE Connectors Floppy5V 8xAGP Pro Slot *P4SCT/P4ST+II AGP SlotPage No Power Troubleshooting ProceduresBefore Power On No VideoTechnical Support Procedures Memory ErrorsLosing the System’s Setup Configuration Frequently Asked Questions Question How do I update my BIOS?Question What type of memory does my motherboard support? Question Whats on the CD that came with my motherboard? P4SCT/P4SCT+/P4SCT+II PCI IRQsReturning Merchandise for Service Page Starting the Setup Utility System BiosHow To Change the Configuration Data IntroductionMain Bios Setup Menu Running SetupMain Bios Setup Press DEL to enter SetupLegacy Diskette a Access ModeDate/Time Legacy Diskette BQuick Boot Advanced Bios SetupAdvanced Bios Features Quiet BootAdvanced Chipset Control Serial ATA Port0/1 mode ECC ConfigurationSata Mode CSA LAN Giga-LANCPU THRM-Throttling 3 I/O Device ConfigurationUSB Legacy Support Keyboard Input ClockUR2 Duplex Mode Uart Mode SelectIR Transmission Delay Use IR PinsKB Power On Password PnP ConfigurationPower On Function Hot Key Power OnConsole Redirection Agent after Boot CPU Warning TemperatureHardware Monitor Processor & Clock Options Password Check Set Supervisor PasswordSet User Password SecurityHard Disk Boot Priority BootCD ROM Drives Boot Priority First Boot DeviceExit Load Fail-Safe Defaults Load Optimized DefaultsDiscard Changes Appendix a Bios Post Messages Page Appendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Post hex DescriptionAppendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix B Award Bios Post Codes Super P4SCT/P4SCT+//P4SCT+II User’s Manual Appendix C Software Installation Instructions ATA Operate Mode Combined ModeEnhanced Mode Appendix C Software Installation Instructions Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays Deleting Arrays From the ARC menu, select Array Configuration Utility ACUViewing Array Properties RAID 1 only-the following prompt is also displayedCreating Arrays To create an arrayAssigning Array Properties Raid Level Create Via When Appropriate When you are finished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayAdding/Deleting Hotspares Initializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Disk Utilities To access the disk utilitiesPage To Exit Adaptec RAID Configuration Utility You can choose from the following optionsInstalling Intels Hance Rapids Driver by Adaptec and the OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control