SUPER MICRO Computer SUPER, P3TDDR PnP/PCI Configurations, CPU L2 Cache ECC Checking, CPU Ratio

Page 61

Chapter 4: Award BIOS

CPU L2 Cache ECC Checking

Set this option to "Enabled" to activate the ECC checking of the CPU L2 cache. The settings are "Disabled" and "Enabled".

Processor Number Feature

Set this option to "Enabled" to make your CPU identification number available to applications and to be (potentially) reported. The settings are "Disabled" and "Enabled". Use "Disabled" if you are concerned about User ID privacy.

CPU Ratio

This option allows the user to set the CPU clock/FSB speed ratio. The settings are "x3", "x3.5", "x 4 ", "x4.5", "x5", "x5.5", "x6", "x6.5", "x7", "x7.5", "x8", "x8.5", "x9", "x9.5", "x10", "x10.5", "x12", "x13", "x14", "x15" and "x16".

4-5 PnP/PCI Configurations

Highlight the item "PnP/PCI" on the main menu bar to activate the following screen:

4-17

Image 61

Contents

Super Page About This Manual Manual Organization PrefaceTable of Contents AwardBIOS TroubleshootingAppendices Chapter Introduction ChecklistOverview Headquarters Contacting SupermicroEurope Asia-PacificSuper P3TDDR Super P3TDDR Connectors Description Jumpers Description Default SettingP3TDDR Quick Reference VIA 266T Chipset System Block Diagram CPU Motherboard FeaturesCD Utilities Chipset Overview Recovery from AC Power LossMemory Support and AGP Capability CPU Fan Auto-Off in Sleep Mode Environmental Temperature ControlPC Health Monitoring Hardware Bios Virus Protection Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core CPU Overheat LED and ControlBios Support for USB Keyboard Slow Blinking LED for Suspend-State IndicatorReal Time Clock Wake-Up Alarm Main Switch Override MechanismExternal Modem Ring-On Power SupplyWake-On-LAN WOL Super I/O Precautions Chapter InstallationStatic-Sensitive Devices UnpackingProcessor Processor InstallationHeatsink Mounting the Motherboard in the Chassis Memory Module Installation See Figure Installing DIMMsI/O Port Locations and Definitions I/O Port/Control Panel Connector LocationsFront Control Panel Front Control Panel ConnectorsPower Supply Connector Connecting CablesInfrared Connector Reset Button Power ButtonOverheat LED HDD Hard Disk Drive LED Power LEDATX PS/2 Keyboard and PS/2 Mouse Ports Universal Serial Bus USBWake-On-LAN WOL1 Serial PortsWake-On-Ring WOM1 Chassis Intrusion Fan HeadersExplanation Jumpers Jumper SettingsFront Side Bus Speed Keyboard Wake-Up Cmos ClearScsi Ch A/B Termination VGA Enable/Disable Scsi Enable/DisableSpeaker Enable/Disable LAN Enable/DisableParallel Port, Floppy/Hard Disk Drive and Scsi Connections Parallel Port ConnectorIDE Connectors Floppy ConnectorUltra Wide Scsi Connector Must reboot the system before moving on to the next item on Installing Software DriversTroubleshooting Procedures Chapter TroubleshootingBefore Power On No PowerMemory Errors Technical Support ProceduresFrequently Asked Questions Question Whats in the CD that came with my motherboard? Shared IRQs Returning Merchandise for ServiceSuper P3TDDR User’s Manual System Bios Chapter AwardBIOSHow To Change the Configuration Data Starting the Setup UtilityMain Bios Setup Running SetupMain Setup Features Main Bios Setup MenuDate/Time Drive A/Drive BIDE HDD Auto-Detection Access ModeIDE Primary Master IDE Primary Master/Slave PIOVideo IDE Primary Master/Slave UdmaHalt On Base Memory/Extended Memory/Total MemoryAdvanced Bios Features Advanced Bios SetupBoot Up NumLock Status Quick Power-On Self TestTypematic Rate Setting Auto Detect DIMM/PCI CLKTypematic Rate Chars/Sec Typematic DelayOS Select For Dram 64MB Pwron After PWR-FailAdvanced Chipset Features Video Bios Shadow System Bios CacheableHost & AGP Bridge Control Memory Parity / ECC CheckIDE Prefetch Mode PCI Delayed TransitionPCI Master 0 WS Write On-Chip IDE Channel 10/11Onboard FDC Controller Integrated Peripherals IR Transmission Delay Uart Mode Select UR2 Duplex Mode Use IR PinsEPP Mode Select Parallel Port ModeECP Mode Use DMA Hardware Monitors CPU Warning TemperaturesCPU L1 Cache Processor FeaturesCPU L2 Cache Processor Number Feature PnP/PCI ConfigurationsCPU L2 Cache ECC Checking CPU RatioReset Configuration Data PNP OS InstalledPCI Slot 1/2/3 IRQ Select USB and LAN2 IRQ SelectPCI/VGA Palette Snoop Power ManagementAssign IRQ for VGA Assign IRQ for USBSuspend Mode Power Management OptionHDD Power Down Acpi FunctionKB Power On Password Power on FunctionVideo Off Option Video Off MethodHot Key Power On Boot-up DevicesRTC Alarm Resume Boot ROM OrderSecond Boot Device First Boot DeviceThird Boot Device Boot Other DeviceSet Supervisors Password Security SetupSet Users Password Security OptionExit Setup Load Fail-Safe Defaults Save & Exit SetupLoad Optimal Defaults Exit Without SavingError Messages Appendix a AwardBIOS Post MessagesPost Beep Codes Diskette Drives or Types Mismatch Error RUN Setup Memory parity Error at Memory Address Error atMemory Verify Error at Bios ROM checksum error System halted Keyboard error or no keyboard presentMemory test fail Manufacturing Post loopDebuggig LED Encoding Appendix B AwardBIOS Post CodesPost hex Description Appendix B AwardBIOS Post Codes Super P3TDDR User’s Manual Appendix B AwardBIOS Post Codes Super P3TDDR User’s Manual Beep Code Error Message Description Appendix C AwardBIOS Beep CodesSuper P3TDDR User’s Manual