SUPER MICRO Computer P3TDDR, SUPER Memory test fail, Keyboard error or no keyboard present

Page 74

SUPER P3TDDR User’s Manual

FLOPPY DISK(S) fail (80) ® Unable to reset floppy subsystem.

FLOPPY DISK(S) fail (40) ® Floppy Type dismatch.

Hard Disk(s) fail (80)

® HDD reset failed

Hard Disk(s) fail (40)

® HDD controller diagnostics failed.

Hard Disk(s) fail (20)

® HDD initialization error.

Hard Disk(s) fail (10)

® Unable to recalibrate fixed disk.

Hard Disk(s) fail (08)

® Sector Verify failed.

Keyboard is locked out - Unlock the key.

BIOS detect the keyboard is locked. P17 of the keyboard controller is pulled low.

Keyboard error or no keyboard present.

Cannot initialize the keyboard. Make sure that the keyboard is attached correctly and no keys are being pressed during the boot.

Manufacturing POST loop.

System will repeat POST procedure infinitely while the P15 of keyboard controller is pulled low. This is also used for M/B burn in testing.

BIOS ROM checksum error - System halted.

The checksum of ROM address F0000H-FFFFFH is bad.

Memory test fail..

BIOS reports the a memory test fail if the onboard memory has an error.

A-4

Page 73 Page 75
Image 74
Page 73 Page 75
Contents
Super Page Preface About This Manual Manual OrganizationTable of Contents Troubleshooting AwardBIOSAppendices Overview ChecklistChapter Introduction Europe Contacting SupermicroHeadquarters Asia-PacificSuper P3TDDR Super P3TDDR P3TDDR Quick Reference Jumpers Description Default SettingConnectors Description VIA 266T Chipset System Block Diagram Motherboard Features CPUCD Utilities Memory Support and AGP Capability Recovery from AC Power LossChipset Overview PC Health Monitoring Environmental Temperature ControlCPU Fan Auto-Off in Sleep Mode Auto-Switching Voltage Regulator for the CPU Core Acpi FeaturesHardware Bios Virus Protection CPU Overheat LED and ControlReal Time Clock Wake-Up Alarm Slow Blinking LED for Suspend-State IndicatorBios Support for USB Keyboard Main Switch Override MechanismWake-On-LAN WOL Power SupplyExternal Modem Ring-On Super I/O Static-Sensitive Devices Chapter InstallationPrecautions UnpackingHeatsink Processor InstallationProcessor Mounting the Motherboard in the Chassis Installing DIMMs Memory Module Installation See FigureI/O Port/Control Panel Connector Locations I/O Port Locations and DefinitionsFront Control Panel Connectors Front Control PanelInfrared Connector Connecting CablesPower Supply Connector Overheat LED Power ButtonReset Button ATX PS/2 Keyboard and PS/2 Mouse Ports Power LEDHDD Hard Disk Drive LED Universal Serial Bus USBWake-On-Ring WOM1 Serial PortsWake-On-LAN WOL1 Fan Headers Chassis IntrusionFront Side Bus Speed Jumper SettingsExplanation Jumpers Scsi Ch A/B Termination Cmos ClearKeyboard Wake-Up Speaker Enable/Disable Scsi Enable/DisableVGA Enable/Disable LAN Enable/DisableParallel Port Connector Parallel Port, Floppy/Hard Disk Drive and Scsi ConnectionsFloppy Connector IDE ConnectorsUltra Wide Scsi Connector Installing Software Drivers Must reboot the system before moving on to the next item onBefore Power On Chapter TroubleshootingTroubleshooting Procedures No PowerTechnical Support Procedures Memory ErrorsFrequently Asked Questions Question Whats in the CD that came with my motherboard? Returning Merchandise for Service Shared IRQsSuper P3TDDR User’s Manual How To Change the Configuration Data Chapter AwardBIOSSystem Bios Starting the Setup UtilityRunning Setup Main Bios SetupDate/Time Main Bios Setup MenuMain Setup Features Drive A/Drive BIDE Primary Master Access ModeIDE HDD Auto-Detection IDE Primary Master/Slave PIOHalt On IDE Primary Master/Slave UdmaVideo Base Memory/Extended Memory/Total MemoryAdvanced Bios Setup Advanced Bios FeaturesTypematic Rate Setting Quick Power-On Self TestBoot Up NumLock Status Auto Detect DIMM/PCI CLKOS Select For Dram 64MB Typematic DelayTypematic Rate Chars/Sec Pwron After PWR-FailAdvanced Chipset Features Host & AGP Bridge Control System Bios CacheableVideo Bios Shadow Memory Parity / ECC CheckPCI Master 0 WS Write PCI Delayed TransitionIDE Prefetch Mode On-Chip IDE Channel 10/11Integrated Peripherals Onboard FDC ControllerUR2 Duplex Mode Uart Mode SelectIR Transmission Delay Use IR PinsECP Mode Use DMA Parallel Port ModeEPP Mode Select CPU Warning Temperatures Hardware MonitorsCPU L2 Cache Processor FeaturesCPU L1 Cache CPU L2 Cache ECC Checking PnP/PCI ConfigurationsProcessor Number Feature CPU RatioPCI Slot 1/2/3 IRQ Select PNP OS InstalledReset Configuration Data USB and LAN2 IRQ SelectAssign IRQ for VGA Power ManagementPCI/VGA Palette Snoop Assign IRQ for USBHDD Power Down Power Management OptionSuspend Mode Acpi FunctionVideo Off Option Power on FunctionKB Power On Password Video Off MethodRTC Alarm Resume Boot-up DevicesHot Key Power On Boot ROM OrderThird Boot Device First Boot DeviceSecond Boot Device Boot Other DeviceSet Users Password Security SetupSet Supervisors Password Security OptionExit Setup Load Optimal Defaults Save & Exit Setup Load Fail-Safe Defaults Exit Without SavingPost Beep Codes Appendix a AwardBIOS Post MessagesError Messages Diskette Drives or Types Mismatch Error RUN Setup Memory Verify Error at Memory Address Error atMemory parity Error at Memory test fail Keyboard error or no keyboard presentBios ROM checksum error System halted Manufacturing Post loopAppendix B AwardBIOS Post Codes Debuggig LED EncodingPost hex Description Appendix B AwardBIOS Post Codes Super P3TDDR User’s Manual Appendix B AwardBIOS Post Codes Super P3TDDR User’s Manual Appendix C AwardBIOS Beep Codes Beep Code Error Message DescriptionSuper P3TDDR User’s Manual
Top Page Image Contents