SUPER MICRO Computer SuperServer 5016I-T Connecting Power Cables, Connecting the Control Panel

Page 37

Chapter 5: Advanced Motherboard Setup

cables (with their locations noted) should be connected. (See the layout on page 5-9 for connector locations.)

•

•

SATA drive data cable (I-SATA0 ~ I-SATA3)

Control Panel cable (JF1)

Important! Make sure the the cables do not come into contact with the fans.

Connecting Power Cables

The X8SIL/X8SIL-F has a 24-pin primary power supply connector (JPW1) for con- nection to the ATX power supply. In addition, an 8-pin processor power connector (JPW2) must also be connected to your power supply. See Section 5-9 for power connector pin deﬁnitions.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indicators.

All JF1 wires have been bundled into a single ribbon cable to simplify this connec- tion. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel PCB board, located just behind the system status LEDs on the chassis. See Chapter 5 for details and pin descriptions.

Figure 5-1. Control Panel Header Pins

16 15

Power LED

HDD LED

NIC1 LED

NIC2 LED OH/Fan Fail LED x (Key)

Ground

Ground

2 1

LED Anode LED Anode LED Anode LED Anode LED Anode x (Key)

Reset (Button) Power (Button)

5-3

Image 37

Contents Super Manual Revision Release Date October 6 About This Manual PrefaceManual Organization Bios Advanced Chassis SetupPreface Table of Contents System Safety Advanced Chassis Setup Bios Page Overview Chapter IntroductionMotherboard Features Chassis Features Intel 3400/3420 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationRack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackAccessing the Inside of the System Figure Checking the Serverboard SetupChecking the Components Accessing the Inside of the System Providing Power Checking the Drive Bay SetupChecking the Drives Checking the AirﬂowPower Reset ButtonChapter System Interface Control Panel ButtonsHDD Overheat/Fan FailSerial ATA Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting Cables Motherboard InstallationConnecting Data Cables Installing to the ChassisConnecting the Control Panel Connecting Power CablesI/O Ports Processor and Heatsink InstallationInstalling the LGA1156 Processor Page Installing the Heatsink Installing a Passive CPU HeatsinkRemoving the Heatsink Dimm Installation Installing MemoryMemory Support DDR3 ECC Registered Rdimm Memory Support Memory Population GuidelinesPopulated Any combination Per Channel Dimm Installation Installing an Expansion Card Installing a PCI Expansion CardX8SIL/X8SIL-F Layout Motherboard DetailsX8SIL/X8SIL-F Headers/Connectors Number Description X8SIL/X8SIL-F Jumpers Number Description DefaultX8SIL/X8SIL-F LED Indicators Number Standby PWR LED Indicator Green Solid on PWR OnMain ATX Power Supply Connector Connector DeﬁnitionsProcessor Power Connector Power ButtonOverheat OH/Fan Fail Power On LEDATX PS/2 Keyboard and PS/2 Mouse Ports Chassis IntrusionFan Headers Onboard SpeakerSerial Ports SpeakerUniversal Serial Bus USB LAN1/LAN2 Ethernet PortsPower Supply I2C Connector Onboard Power LEDAlarm Reset Sgpio 0/1 HeadersVGA Enable Jumper SettingsExplanation of Jumpers Cmos ClearPCI Slot SMB Enable LAN1/LAN2 Enable/DisableUSB Wake-Up BMC JumperLAN1/2 LEDs Onboard IndicatorsIpmi Dedicated LAN LEDs Ipmi Heartbeat LEDSata and Floppy Drive Connections Floppy ConnectorSata Ports Page Static-Sensitive Devices Chapter Advanced Chassis SetupChassis Front View Control PanelSystem Fan Failure System FansReplacing System Cooling Fans Accessing the Drive Bays Drive Bay Installation/RemovalSerial ATA Drive Installation Mounting a Sata Drive in a Drive Carrier Installing/Removing Sata DrivesInstalling a DVD-ROM Drive DVD-ROM Drive InstallationPower Supply Failure Power SupplyReplacing the Power Supply Page How To Change the Conﬁguration Data Starting Bios Setup UtilityChapter IntroductionHow to Start the Setup Utility Main SetupProcessor System Time/System DateSystem Memory Xboot Feature Advanced Setup ConﬁgurationsXProcessor & Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPUIntel Eist Technology XAdvanced Chipset Control Xsata / Floppy Conﬁguration LBA/Large Mode IDE Detect Timeout secPIO Mode TypeDMA Mode XPCI/PnP Conﬁguration XSuper IO Device Conﬁguration XRemote Access Conﬁguration System Temperature CPU Overheat AlarmCPU Temperature XHardware Health ConﬁgurationFan Speed Control Modes Xacpi Conﬁguration Xipmi Conﬁguration X8SIL-F Only XIntel TXT LT Conﬁguration XEvent Log ConﬁgurationBios AS Sclean Bios AC Scheck Supervisor Password Security SettingsUser Password Change Supervisor PasswordXBoot Device Priority Boot SettingsBoot Sector Virus Protection Exit Options Retry Boot DevicesXRemovable Drives XCD/DVD DrivesLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes and Exit Discard ChangesPage Recoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Installing Windows to a RAID System Appendix B Installing WindowsInstalling Windows to a Non-RAID System Appendix C System Speciﬁcations BiosWeight Appendix C System Speciﬁcations