SUPER MICRO Computer SuperServer 5016I-T user manual Onboard Power LED, Power Supply I2C Connector

Page 53

Chapter 5: Advanced Motherboard Setup

Onboard Power LED

An onboard Power LED header is located at JLED. This Power LED header is connected to Control Panel header located at JF1 to indicate the status of system power. See the table on the right for pin deﬁnitions.

Power Supply I2C Connector

The Power Supply (I2C) connector is located at SMB_PS1 and is used to monitor the status of the power supply, fan and system temperature. See the table on the right for pin deﬁnitions.

T-SGPIO 0/1 Headers

Two T-SGPIO (Serial-Link General Purpose Input/Output) headers are

Onboard PWR LED

Pin Deﬁnitions

Pin# Deﬁnition

1VCC

2No Connection

3Connection to PWR LED in JF1

PWR Supply I2C

Pin Deﬁnitions

Pin# Deﬁnition

1Clock

2Data

3PWR Fail

4Ground

53.3V

Serial_Link-SGPIO

Pin Deﬁnitions

located near the SATA connectors on the motherboard. These headers are used to communicate with the enclosure management chip in the system. See the table on the right for

Pin#

1

3

5

7

Deﬁnition

NC

Ground

Load

Clock

Pin 2 4 6 8

Deﬁnition

NC

DATA Out

Ground

NC

pin deﬁnitions.

Alarm Reset

If three power supplies are installed and Alarm Reset (JAR) is connected, the system will notify you when any of the three power modules fail. Connect JAR to a micro-switch to turn off the alarm that is activated when a power module fails. See the table on the right for pin deﬁnitions.

NC = No Connection

Alarm Reset
Pin Deﬁnitions

Pin Setting		Deﬁnition

Pin 1		Ground

Pin 2		+5V

5-19

Image 53

Contents Super Manual Revision Release Date October 6 Manual Organization PrefaceAbout This Manual Bios Advanced Chassis SetupPreface Table of Contents System Safety Advanced Chassis Setup Bios Page Overview Chapter IntroductionMotherboard Features Chassis Features Intel 3400/3420 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PaciﬁcPage Unpacking the System Chapter Server InstallationPreparing for Setup Rack Precautions Choosing a Setup LocationRack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Components Checking the Serverboard SetupAccessing the Inside of the System Figure Accessing the Inside of the System Providing Power Checking the Drive Bay SetupChecking the Drives Checking the AirﬂowPower Reset ButtonChapter System Interface Control Panel ButtonsHDD Overheat/Fan FailSerial ATA Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting Cables Motherboard InstallationConnecting Data Cables Installing to the ChassisConnecting the Control Panel Connecting Power CablesI/O Ports Processor and Heatsink InstallationInstalling the LGA1156 Processor Page Installing the Heatsink Installing a Passive CPU HeatsinkRemoving the Heatsink Memory Support Installing MemoryDimm Installation Populated Any combination Per Channel Memory Population GuidelinesDDR3 ECC Registered Rdimm Memory Support Dimm Installation Installing an Expansion Card Installing a PCI Expansion CardX8SIL/X8SIL-F Layout Motherboard DetailsX8SIL/X8SIL-F Headers/Connectors Number Description X8SIL/X8SIL-F Jumpers Number Description DefaultX8SIL/X8SIL-F LED Indicators Number Standby PWR LED Indicator Green Solid on PWR OnMain ATX Power Supply Connector Connector DeﬁnitionsProcessor Power Connector Power ButtonOverheat OH/Fan Fail Power On LEDATX PS/2 Keyboard and PS/2 Mouse Ports Chassis IntrusionFan Headers Onboard SpeakerSerial Ports SpeakerUniversal Serial Bus USB LAN1/LAN2 Ethernet PortsPower Supply I2C Connector Onboard Power LEDAlarm Reset Sgpio 0/1 HeadersVGA Enable Jumper SettingsExplanation of Jumpers Cmos ClearPCI Slot SMB Enable LAN1/LAN2 Enable/DisableUSB Wake-Up BMC JumperLAN1/2 LEDs Onboard IndicatorsIpmi Dedicated LAN LEDs Ipmi Heartbeat LEDSata Ports Floppy ConnectorSata and Floppy Drive Connections Page Static-Sensitive Devices Chapter Advanced Chassis SetupChassis Front View Control PanelReplacing System Cooling Fans System FansSystem Fan Failure Serial ATA Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays Mounting a Sata Drive in a Drive Carrier Installing/Removing Sata DrivesInstalling a DVD-ROM Drive DVD-ROM Drive InstallationReplacing the Power Supply Power SupplyPower Supply Failure Page How To Change the Conﬁguration Data Starting Bios Setup UtilityChapter IntroductionHow to Start the Setup Utility Main SetupSystem Memory System Time/System DateProcessor Xboot Feature Advanced Setup ConﬁgurationsXProcessor & Clock Options Intel Eist Technology Hardware Prefetcher Available when supported by the CPUActive Processor Cores XAdvanced Chipset Control Xsata / Floppy Conﬁguration LBA/Large Mode IDE Detect Timeout secPIO Mode TypeDMA Mode XPCI/PnP Conﬁguration XSuper IO Device Conﬁguration XRemote Access Conﬁguration System Temperature CPU Overheat AlarmCPU Temperature XHardware Health ConﬁgurationFan Speed Control Modes Xacpi Conﬁguration Xipmi Conﬁguration X8SIL-F Only XIntel TXT LT Conﬁguration XEvent Log ConﬁgurationBios AS Sclean Bios AC Scheck Supervisor Password Security SettingsUser Password Change Supervisor PasswordBoot Sector Virus Protection Boot SettingsXBoot Device Priority Exit Options Retry Boot DevicesXRemovable Drives XCD/DVD DrivesLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes and Exit Discard ChangesPage Recoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Installing Windows to a RAID System Appendix B Installing WindowsInstalling Windows to a Non-RAID System Appendix C System Speciﬁcations BiosWeight Appendix C System Speciﬁcations