SUPER MICRO Computer 2042G-TRF Installing the Processor and Heatsink, Installation Procedure

Page 37

Chapter 5: Advanced Serverboard Setup

5-5 Installing the Processor and Heatsink

!

Exercise extreme caution when handling and installing the processor. Always connect the power cord last and always remove it before adding, removing or changing any hardware components.

Installation Procedure

Follow the procedures as listed below to install the motherboard into a chassis.

1.Install the processor(s) and the heatsink(s).

2.Install the motherboard in the chassis.

3.Install the memory and add-on cards.

4.Finally, connect the cables and install the drivers.

Installing the Processors

1.Begin by removing the cover plate that protects the CPU. Lift the lever on the CPU socket until it points straight up.

2.With the lever raised, lift open the silver CPU retention plate.

5-5

Image 37

Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Interface Advanced Chassis Setup Appendix C System Speciﬁcations Page Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSAS AS-2042G-6RF Only Serial ATAEthernet Ports Other FeaturesOnboard Controllers/Ports Graphics ControllerServer Chassis Features AMD SR5690/SP5100 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PaciﬁcPreparing for Setup Chapter Server InstallationUnpacking the System Choosing a Setup Location Rack Mounting Considerations Ambient Operating TemperatureInstalling the Inner Rails Installing the System into a RackInstalling the Outer Rails Identifying the Sections of the Rack RailsInstalling the Server into a Rack Installing the Server into the RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components and Setup Providing Power Preparing to Power OnChecking the Drives Checking the AirﬂowPage Power ResetChapter System Interface Control Panel ButtonsControl Panel LEDs Power FailOverheat/Fan Fail HDD SAS Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard CR2032 Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Installing to the Chassis Serverboard InstallationUnpacking Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelRear I/O Ports I/O PortsInstallation Procedure Installing the Processor and HeatsinkInstalling the Processors Socket, which may damage SNK-0043P Heatsink Installing a Passive CPU HeatsinkInstalling Memory Installing MemorySupport Maximum MemoryChannel # Dimms CPUPossible System Memory Allocation & Availability Per Channel Dimm Populations OptionsDimm Type Max. MHz Max. GB 5V DIMMs 35V DIMMsAdding PCI Add-On Cards Installing an Add-on CardServerboard Details Jumper Description Default SettingH8QG6/i-F Quick Reference Connector Description Advanced Serverboard SetupPower Connectors Connector DeﬁnitionsReset Connector HDD/FP UID Switch Power Fail LEDPower LED Connector Overheat OH/Fan Fail/PWR Fail/UIDUniversal Serial Bus Ports Video ConnectorUSB Headers Fan HeadersSMBus Header Power I2CWake-On-LAN Chassis Intrusion Power LED/SpeakerOverheat LED ATX PS/2 Keyboard and PS/2 Mouse PortsUnit Identiﬁer Button Compact Flash Card PWR ConnectorTrusted Platform Module Header LAN1/2 Ethernet PortsExplanation of Jumpers Jumper SettingsCmos Clear JBT1 contact padsVGA Enable/Disable Watch Dog Enable/DisableLAN1/2 Enable/Disable SAS Enable/DisableBMC Jumper Enable JPB1 Jumper Settings Backpanel USB Wake-Up Enable JPUSB1 Jumper SettingsUSB Wake-Up BMC JumperPower LED Onboard IndicatorsLAN1/LAN2 LEDs Dedicated Ipmi LAN LEDsSata Ports SAS and Sata Drive ConnectionsSAS Ports H8QG6-F Only Sata Ports Pin DeﬁnitionsEnabling Sata RAID Installing the OS/SATA DriverSerial ATA Sata Building a Driver DisketteBios Setup Screen Enabling Sata RAID in the BiosInstalling the RAID Driver During OS Installation Using the Adaptec RAID UtilityDriver/Tool Installation Display Screen Installing DriversSupero Doctor Page Page System Fans Control PanelPort Replacing System Fans System Fan FailureRemoving a fan Accessing the Drive Bays Drive Bay Installation/RemovalSAS/SATA Drive Installation Installing a new fanInstalling/removing SAS/SATA drives Page SAS/SATA Drive Backplane DVD-ROM Drive InstallationSAS/SATA Backplane Connections Power Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supplyRemoving a Power Supply Module Page Chapter Starting the Setup UtilityIntroduction Boot Features Advanced Settings MenuMain Menu  Processor & Clock Options NorthBridge Chipset Conﬁguration Memory Conﬁguration Advanced Chipset ControlDRAM Timing Conﬁguration ECC ConﬁgurationPrimary/Secondary/Third IDE Master/Slave IDE/SATA ConﬁgurationIDE Detect Timeout Sec DMA ModeA.R.T Bit Data TransferSuperI/O Conﬁguration  PCI/PNP ConﬁgurationRemote Access Conﬁguration System Fan Monitor Hardware Health ConﬁgurationACPI Conﬁguration View BMC System Event Log IPMI ConﬁgurationSet LAN Conﬁguration IP AddressEvent Log Conﬁguration Security Settings MenuMAC Address Subnet MaskBoot Settings Menu Network Drives Exit MenuAmibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Installing Windows to a RAID System Appendix B Installing WindowsInstalling Windows to a Non-RAID System Appendix C System Speciﬁcations Power Supply WeightExpansion Slots ServerboardRegulatory Compliance From front