SUPER MICRO Computer 2042G-6RF, 2042G-TRF, AS2042G72RF4 user manual IDE/SATA Configuration

Page 78

A+ SERVER 2042G-TRF/6RF User's Manual

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support if there are no USB devices installed in the system. "Auto" disabled Legacy support if no USB devices are connected. The options are Disabled, Enabled and Auto.

IDE/SATA Configuration

On Chip SATA Channel

This setting allows you to Enable or Disable the OnChip SATA channel.

On Chip SATA Type

Use this setting to set the On Chip SATA type. Options include Native IDE, RAID, AHCI and Legacy IDE.

SATA IDE Combined Mode

This setting allows you to Enable or Disable the SATA IDE combined mode.

PATA Channel Configuration

This allows you to set PATA channel configuration. Options include SATA as Primary or SATA as secondary.

Primary/Secondary/Third IDE Master/Slave

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto.

Block (Multi-Sector Transfer)

Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt. Select "Disabled" to allow the data to be transferred from and to the device one sector at a time. Select "Auto" to allows the data transfer from and to the device occur multiple sectors at a time if the device supports it. The options are Auto and Disabled.

PIO Mode

PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases. The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow BIOS to auto detect the PIO mode.

7-6

Image 78
Contents Super Page Preface About This ManualManual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents System Interface Advanced Chassis Setup Appendix C System Specifications Page Chapter Introduction OverviewSAS AS-2042G-6RF Only Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesEthernet Ports Graphics ControllerServer Chassis Features AMD SR5690/SP5100 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificChapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the Outer Rails Installing the System into a RackInstalling the Inner Rails Identifying the Sections of the Rack RailsInstalling the Server into the Rack Installing the Server into a RackChecking the Serverboard Setup Accessing the Inside of the SystemChecking the Components and Setup Checking the Drives Preparing to Power OnProviding Power Checking the AirflowPage Chapter System Interface ResetPower Control Panel ButtonsPower Fail Control Panel LEDsOverheat/Fan Fail SAS Drive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard CR2032 BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Serverboard Installation Installing to the ChassisUnpacking Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelI/O Ports Rear I/O PortsInstalling the Processor and Heatsink Installation ProcedureInstalling the Processors Socket, which may damage Installing a Passive CPU Heatsink SNK-0043P HeatsinkSupport Installing MemoryInstalling Memory Maximum Memory# Dimms CPU ChannelDimm Type Per Channel Dimm Populations OptionsPossible System Memory Allocation & Availability Max. MHz Max. GB 5V DIMMs 35V DIMMsInstalling an Add-on Card Adding PCI Add-On CardsJumper Description Default Setting Serverboard DetailsH8QG6/i-F Quick Reference Advanced Serverboard Setup Connector DescriptionConnector Definitions Power ConnectorsReset Connector Power LED Connector Power Fail LEDHDD/FP UID Switch Overheat OH/Fan Fail/PWR Fail/UIDUSB Headers Video ConnectorUniversal Serial Bus Ports Fan HeadersPower I2C SMBus HeaderWake-On-LAN Overheat LED Power LED/SpeakerChassis Intrusion ATX PS/2 Keyboard and PS/2 Mouse PortsTrusted Platform Module Header Compact Flash Card PWR ConnectorUnit Identifier Button LAN1/2 Ethernet PortsCmos Clear Jumper SettingsExplanation of Jumpers JBT1 contact padsLAN1/2 Enable/Disable Watch Dog Enable/DisableVGA Enable/Disable SAS Enable/DisableUSB Wake-Up Backpanel USB Wake-Up Enable JPUSB1 Jumper SettingsBMC Jumper Enable JPB1 Jumper Settings BMC JumperLAN1/LAN2 LEDs Onboard IndicatorsPower LED Dedicated Ipmi LAN LEDsSAS Ports H8QG6-F Only SAS and Sata Drive ConnectionsSata Ports Sata Ports Pin DefinitionsSerial ATA Sata Installing the OS/SATA DriverEnabling Sata RAID Building a Driver DisketteEnabling Sata RAID in the Bios Bios Setup ScreenUsing the Adaptec RAID Utility Installing the RAID Driver During OS InstallationInstalling Drivers Driver/Tool Installation Display ScreenSupero Doctor Page Page Control Panel System FansPort System Fan Failure Replacing System FansRemoving a fan SAS/SATA Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays Installing a new fanInstalling/removing SAS/SATA drives Page DVD-ROM Drive Installation SAS/SATA Drive BackplaneSAS/SATA Backplane Connections Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving a Power Supply Module Page Starting the Setup Utility ChapterIntroduction Advanced Settings Menu Boot FeaturesMain Menu  Processor & Clock Options Advanced Chipset Control NorthBridge Chipset Configuration Memory ConfigurationECC Configuration DRAM Timing ConfigurationIDE/SATA Configuration Primary/Secondary/Third IDE Master/SlaveA.R.T DMA ModeIDE Detect Timeout Sec Bit Data Transfer PCI/PNP Configuration SuperI/O ConfigurationRemote Access Configuration Hardware Health Configuration System Fan MonitorACPI Configuration Set LAN Configuration IPMI ConfigurationView BMC System Event Log IP AddressMAC Address Security Settings MenuEvent Log Configuration Subnet MaskBoot Settings Menu Exit Menu Network DrivesAppendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description Page Appendix B Installing Windows Installing Windows to a RAID SystemInstalling Windows to a Non-RAID System Appendix C System Specifications Expansion Slots WeightPower Supply ServerboardRegulatory Compliance From front