SUPER MICRO Computer 2042G-TRF, 2042G-6RF, AS2042G72RF4 user manual Appendix C System Speciﬁcations

Page 91

Appendix C: System Speciﬁcations

Appendix C

System Speciﬁcations

Processors

Quad AMD Opteron 6100 series (AMD Socket G34 type) processors

Note: please refer to our website for details on supported processors.

Chipset

One AMD SR5690 chipset and one SP5100 Southbridge chipset

BIOS

16 Mb AMIBIOS SPI Flash ROM

Memory Capacity

Thirty-Two (32) single/dual/tri/quad channel DIMM slots supporting up to 512 GB of DDR3-1333/1066/800 registered ECC or 128GB of DDR3 Unbuffered ECC/ non-ECC SDRAM

Note: interleaved memory requires DIMMs to be installed in pairs - refer to Section 5-6 for details.

SATA Controller

AMD SR5690 on-chip controller to support six 3 Gb/s Serial ATA (RAID 0, 1, 10 supported)

SAS Controller

Onboard LSI-2008 SAS2 controller for eight SAS drives (RAID 0, 1 and 10 supported). RAID 5 is supported with the use of an optional RAIDKey for RAID 5 SAS support (only on H8QG6-F serverboard)

Drive Bays

Six (6) hot-swap drive bays to house six (6) standard SAS drives

Peripheral Drives/Bays

One (1) slim DVD-ROM drive

C-1

Image 91

Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Interface Advanced Chassis Setup Appendix C System Speciﬁcations Page Overview Chapter IntroductionSerial ATA Serverboard FeaturesProcessors Memory SAS AS-2042G-6RF OnlyGraphics Controller Other FeaturesEthernet Ports Onboard Controllers/PortsServer Chassis Features AMD SR5690/SP5100 Chipset System Block Diagram Asia-Paciﬁc Contacting SupermicroHeadquarters EuropePreparing for Setup Chapter Server InstallationUnpacking the System Choosing a Setup Location Rack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Outer RailsInstalling the Server into a Rack Installing the Server into the RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components and Setup Checking the Airﬂow Preparing to Power OnProviding Power Checking the DrivesPage Control Panel Buttons ResetPower Chapter System InterfaceControl Panel LEDs Power FailOverheat/Fan Fail HDD SAS Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard CR2032 Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Installing to the Chassis Serverboard InstallationUnpacking Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesRear I/O Ports I/O PortsInstallation Procedure Installing the Processor and HeatsinkInstalling the Processors Socket, which may damage SNK-0043P Heatsink Installing a Passive CPU HeatsinkMaximum Memory Installing MemoryInstalling Memory SupportChannel # Dimms CPUMax. MHz Max. GB 5V DIMMs 35V DIMMs Per Channel Dimm Populations OptionsPossible System Memory Allocation & Availability Dimm TypeAdding PCI Add-On Cards Installing an Add-on CardServerboard Details Jumper Description Default SettingH8QG6/i-F Quick Reference Connector Description Advanced Serverboard SetupPower Connectors Connector DeﬁnitionsReset Connector Overheat OH/Fan Fail/PWR Fail/UID Power Fail LEDHDD/FP UID Switch Power LED ConnectorFan Headers Video ConnectorUniversal Serial Bus Ports USB HeadersSMBus Header Power I2CWake-On-LAN ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerChassis Intrusion Overheat LEDLAN1/2 Ethernet Ports Compact Flash Card PWR ConnectorUnit Identiﬁer Button Trusted Platform Module HeaderJBT1 contact pads Jumper SettingsExplanation of Jumpers Cmos ClearSAS Enable/Disable Watch Dog Enable/DisableVGA Enable/Disable LAN1/2 Enable/DisableBMC Jumper Backpanel USB Wake-Up Enable JPUSB1 Jumper SettingsBMC Jumper Enable JPB1 Jumper Settings USB Wake-UpDedicated Ipmi LAN LEDs Onboard IndicatorsPower LED LAN1/LAN2 LEDsSata Ports Pin Deﬁnitions SAS and Sata Drive ConnectionsSata Ports SAS Ports H8QG6-F OnlyBuilding a Driver Diskette Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataBios Setup Screen Enabling Sata RAID in the BiosInstalling the RAID Driver During OS Installation Using the Adaptec RAID UtilityDriver/Tool Installation Display Screen Installing DriversSupero Doctor Page Page System Fans Control PanelPort Replacing System Fans System Fan FailureRemoving a fan Installing a new fan Drive Bay Installation/RemovalAccessing the Drive Bays SAS/SATA Drive InstallationInstalling/removing SAS/SATA drives Page SAS/SATA Drive Backplane DVD-ROM Drive InstallationSAS/SATA Backplane Connections Removing the power supply Power SupplyPower Supply Failure Removing/Replacing the Power SupplyRemoving a Power Supply Module Page Chapter Starting the Setup UtilityIntroduction Boot Features Advanced Settings MenuMain Menu  Processor & Clock Options NorthBridge Chipset Conﬁguration Memory Conﬁguration Advanced Chipset ControlDRAM Timing Conﬁguration ECC ConﬁgurationPrimary/Secondary/Third IDE Master/Slave IDE/SATA ConﬁgurationBit Data Transfer DMA ModeIDE Detect Timeout Sec A.R.TSuperI/O Conﬁguration  PCI/PNP ConﬁgurationRemote Access Conﬁguration System Fan Monitor Hardware Health ConﬁgurationACPI Conﬁguration IP Address IPMI ConﬁgurationView BMC System Event Log Set LAN ConﬁgurationSubnet Mask Security Settings MenuEvent Log Conﬁguration MAC AddressBoot Settings Menu Network Drives Exit MenuAmibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Installing Windows to a RAID System Appendix B Installing WindowsInstalling Windows to a Non-RAID System Appendix C System Speciﬁcations Serverboard WeightPower Supply Expansion SlotsRegulatory Compliance From front