SUPER MICRO Computer 1022G-URF user manual Checking the Airflow, Providing Power

Page 24

A+ SERVER 1022G-URF User's Manual

Checking the Airflow

Airflow is provided by four sets of 4-cm fans (each set of fans consists of two fans that are mounted back to back). The system component layout was carefully designed to direct sufficient cooling airflow to the components that generate the most heat.

Note that all power and data cables have been routed in such a way that they do not block the airflow generated by the fans.

Providing Power

The last thing you must do is to provide input power to the system. Plug the power cords from the power supply modules into a high-quality power strip that offers protection from electrical noise and power surges.

It is recommended that you use an uninterruptible power supply (UPS).

2-10

Image 24

Contents Super + Server 1022G-URF Users Guide Server Installation About This ManualManual Organization IntroductionAdvanced Serverboard Setup Advanced Chassis SetupBios Contents System Interface Advanced Serverboard Setup Appendix C System Specifications Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA Server Chassis Features PCI Expansion Slots Front Control PanelBackplane Cooling SystemAMD SR5670/SP5100 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPreparing for Setup Choosing a Setup LocationUnpacking the System Page Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Outer Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the SystemChecking the Components Checking the Drive Bay Setup Checking the DrivesProviding Power Checking the AirflowReset Control Panel ButtonsPower Control Panel LEDsInformation LED Informational LED StatusNIC2 Hard Drive Carrier LEDs About Standardized Warning Statements 警告の定義この警告サインは危険を意味します。人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、הרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning 電源切断の警告םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置Restricted Area アクセス制限区域このユニットは、アクセス制限区域に設置されることを想定しています。Battery Handling 電池の取り扱いPage Redundant Power Supplies הדיחיה תאBackplane Voltage バックプレーンの電圧Comply with Local and National Electrical Codes 地方および国の電気規格に準拠機器の取り付けはその地方および国の電気規格に準拠する必要があります。Product Disposal 製品の廃棄Hot Swap Fan Warning ファン・ホットスワップの警告當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。 Power Cable and AC Adapter 電源コードとACアダプターPage Page Chapter Advanced Serverboard Setup Processor and Heatsink Installation Installing the ProcessorsSocket, which may damage Installing a Passive CPU Heatsink SNK-0042P HeatsinkConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsInstalling Memory Installing Memory ModulesMemory Support Top View of DDR3 SlotDimm Population Table # Dimms CPUPossible System Memory Allocation & Availability Installing a PCI Expansion Card Adding PCI CardsPCI Expansion Slots Serverboard Details Super H8DGU-F LayoutJumper Description Default Setting H8DGU-F Quick ReferenceConnector Definitions Power ConnectorsPwon Connector Reset ConnectorPower On LED Overheat/Fan Fail LED OHNMI Button Universal Serial Bus Ports USB HeadersFan Headers Serial PortsUIO Power Connector LAN1/2 Ethernet PortsPower LED/Speaker Chassis IntrusionOverheat LED ATX PS/2 Keyboard and PS/2 Mouse PortsVideo Connector Compact Flash Card PWR ConnectorUnit Identifier Button Jumper Settings Cmos ClearTo Clear Cmos Watch Dog Enable/Disable LAN1/2 Enable/DisableVGA Enable/Disable I2C to PCI-Express SlotOnboard Indicators Power LEDLAN1/LAN2 LEDs Dedicated Ipmi LAN LEDsSata Drive Connections Sata PortsInstalling the OS/SATA Driver Enabling Sata RAIDSerial ATA Sata Building a Driver DisketteEnabling Sata RAID in the Bios Bios Setup ScreenUsing the DotHill and Adaptec RAID Utility DotHill RAID Utility Program ScreenInstalling Software Installing the RAID Driver During OS InstallationSuperDoctor SuperDoctor III Interface Display Screen Health Information Serverboard Battery 11. Installing the Onboard BatteryPage Page Control Panel System FansSystem Fan Failure Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysRemoving the Front Bezel Hard Drive Installation Mounting a Hard Drive in a Drive CarrierDVD-ROM Drive Installation Installing/Removing a Hard DriveRemoving the Chassis Cover Power Supply Removing/Installing a DriveReplacing the Power Supply Removing/Replacing the Power SupplyIntroduction Main MenuAdvanced Settings Menu  Boot FeatureSystem Time/System Date  Processor and Clock Options  Advanced Chipset Control  NorthBridge Configuration Bank Swizzle Mode ECC ModeDram ECC Enable Dram Timing Config IDE Configuration  Primary/Secondary/Third/Fourth IDE Master/SlavePIO Mode DMA ModeIDE Detect Timeout Sec A.R.T PCI/PnP Configuration  SuperIO Device Configuration Remote Access Configuration  Hardware Health Configuration  Acpi Configuration Ipmi Configuration  Set LAN Configuration View BMC System Event Log  Event Log Configuration Boot Menu  Boot Device PrioritySecurity Menu  Hard Disk DrivesExit Menu Appendix a Bios Error Beep Codes Amibios Error Beep CodesPage Appendix B Installing Windows Installing the Windows OS for a RAID SystemInstalling the Windows OS for a Non-RAID System Appendix C System Specifications Expansion Slots Regulatory Compliance