SUPER MICRO Computer 1022G-URF user manual I/O Ports, Front Control Panel Header Pins JF1

Page 54

A+ SERVER 1022G-UTF User's Manual

See the Connector Definitions section in this chapter for details and pin descrip- tions of JF1.

Figure 5-1. Front Control Panel Header Pins (JF1)

20 19 Ground

x (key)

Power LED

HDD LED

NIC1 (Link) LED

NIC2 (Link) LED

OH/Fan Fail LED

Power Fail LED

Ground

Ground

2 1

NMI

x(key) Vcc Vcc

NIC1 (Activity) LED NIC2 (Activity) LED Vcc

Vcc Reset Power

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specification. See Figure 5-2 below for the colors and locations of the various I/O ports.

Figure 5-2. Rear Panel I/O Ports

12 14

1	1	1	1	1	1
1	3	5	6	7	8

	Rear I/O Ports

1.	Keyboard	5.	COM1

2.	PS/2 Mouse	6.	VGA Port

3.	USB0/1	7.	LAN1

4.	IPMI LAN (H8DGU-F only	8.	LAN2

5-6

Image 54

Contents Super + Server 1022G-URF Users Guide Manual Organization Server InstallationAbout This Manual IntroductionAdvanced Serverboard Setup Advanced Chassis SetupBios Contents System Interface Advanced Serverboard Setup Appendix C System Specifications Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA Server Chassis Features Backplane PCI Expansion SlotsFront Control Panel Cooling SystemAMD SR5670/SP5100 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPreparing for Setup Choosing a Setup LocationUnpacking the System Page Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Outer Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the SystemChecking the Components Checking the Drive Bay Setup Checking the DrivesProviding Power Checking the AirflowReset Control Panel ButtonsInformation LED PowerControl Panel LEDs Informational LED StatusNIC2 Hard Drive Carrier LEDs About Standardized Warning Statements 警告の定義この警告サインは危険を意味します。人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、הרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning 電源切断の警告םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置Restricted Area アクセス制限区域このユニットは、アクセス制限区域に設置されることを想定しています。Battery Handling 電池の取り扱いPage Redundant Power Supplies הדיחיה תאBackplane Voltage バックプレーンの電圧Comply with Local and National Electrical Codes 地方および国の電気規格に準拠機器の取り付けはその地方および国の電気規格に準拠する必要があります。Product Disposal 製品の廃棄Hot Swap Fan Warning ファン・ホットスワップの警告當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。 Power Cable and AC Adapter 電源コードとACアダプターPage Page Chapter Advanced Serverboard Setup Processor and Heatsink Installation Installing the ProcessorsSocket, which may damage Installing a Passive CPU Heatsink SNK-0042P HeatsinkConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsMemory Support Installing MemoryInstalling Memory Modules Top View of DDR3 SlotDimm Population Table # Dimms CPUPossible System Memory Allocation & Availability Installing a PCI Expansion Card Adding PCI CardsPCI Expansion Slots Serverboard Details Super H8DGU-F LayoutJumper Description Default Setting H8DGU-F Quick ReferencePwon Connector Connector DefinitionsPower Connectors Reset ConnectorPower On LED Overheat/Fan Fail LED OHNMI Button Fan Headers Universal Serial Bus PortsUSB Headers Serial PortsUIO Power Connector LAN1/2 Ethernet PortsOverheat LED Power LED/SpeakerChassis Intrusion ATX PS/2 Keyboard and PS/2 Mouse PortsVideo Connector Compact Flash Card PWR ConnectorUnit Identifier Button Jumper Settings Cmos ClearTo Clear Cmos VGA Enable/Disable Watch Dog Enable/DisableLAN1/2 Enable/Disable I2C to PCI-Express SlotLAN1/LAN2 LEDs Onboard IndicatorsPower LED Dedicated Ipmi LAN LEDsSata Drive Connections Sata PortsSerial ATA Sata Installing the OS/SATA DriverEnabling Sata RAID Building a Driver DisketteEnabling Sata RAID in the Bios Bios Setup ScreenUsing the DotHill and Adaptec RAID Utility DotHill RAID Utility Program ScreenInstalling Software Installing the RAID Driver During OS InstallationSuperDoctor SuperDoctor III Interface Display Screen Health Information Serverboard Battery 11. Installing the Onboard BatteryPage Page Control Panel System FansSystem Fan Failure Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysRemoving the Front Bezel Hard Drive Installation Mounting a Hard Drive in a Drive CarrierDVD-ROM Drive Installation Installing/Removing a Hard DriveRemoving the Chassis Cover Power Supply Removing/Installing a DriveReplacing the Power Supply Removing/Replacing the Power SupplyIntroduction Main MenuAdvanced Settings Menu  Boot FeatureSystem Time/System Date  Processor and Clock Options  Advanced Chipset Control  NorthBridge Configuration Dram ECC Enable Bank Swizzle ModeECC Mode Dram Timing Config IDE Configuration  Primary/Secondary/Third/Fourth IDE Master/SlaveIDE Detect Timeout Sec PIO ModeDMA Mode A.R.T PCI/PnP Configuration  SuperIO Device Configuration Remote Access Configuration  Hardware Health Configuration  Acpi Configuration Ipmi Configuration  Set LAN Configuration View BMC System Event Log  Event Log Configuration Security Menu Boot Menu Boot Device Priority  Hard Disk DrivesExit Menu Appendix a Bios Error Beep Codes Amibios Error Beep CodesPage Appendix B Installing Windows Installing the Windows OS for a RAID SystemInstalling the Windows OS for a Non-RAID System Appendix C System Specifications Expansion Slots Regulatory Compliance