SUPER MICRO Computer 1022G-URF user manual הדיחיה תא, Redundant Power Supplies

Page 40

A+ Server 1022G-URF User's Manual

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告

此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar por completo el suministro de energía, deben desconectarse todas las conexiones.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.

דחא קפסמ רתוי םייק םא

!הרהזא ןקורל תנמ לע םירוביחה לכ תא ריסהל שי .קפס לש דחא רוביחמ רתוי שי הדחיל

.הדיחיה תא

4-12

Image 40
Contents Super + Server 1022G-URF Users Guide Server Installation About This ManualManual Organization IntroductionAdvanced Chassis Setup Advanced Serverboard SetupBios Contents System Interface Advanced Serverboard Setup Appendix C System Specifications Chapter Introduction OverviewProcessors Memory Serverboard FeaturesSerial ATA Server Chassis Features PCI Expansion Slots Front Control PanelBackplane Cooling SystemAMD SR5670/SP5100 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificChoosing a Setup Location Preparing for SetupUnpacking the System Page Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Outer Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components Checking the Drive Bay Setup Checking the DrivesProviding Power Checking the AirflowReset Control Panel ButtonsPower Control Panel LEDsInformation LED Informational LED StatusNIC2 Hard Drive Carrier LEDs About Standardized Warning Statements 警告の定義 この警告サインは危険を意味します。 人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、הרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning 電源切断の警告םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置Restricted Area アクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。Battery Handling 電池の取り扱いPage Redundant Power Supplies הדיחיה תאBackplane Voltage バックプレーンの電圧Comply with Local and National Electrical Codes 地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。Product Disposal 製品の廃棄Hot Swap Fan Warning ファン・ホットスワップの警告當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter 電源コードとACアダプターPage Page Chapter Advanced Serverboard Setup Processor and Heatsink Installation Installing the ProcessorsSocket, which may damage Installing a Passive CPU Heatsink SNK-0042P HeatsinkConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsInstalling Memory Installing Memory ModulesMemory Support Top View of DDR3 SlotDimm Population Table # Dimms CPUPossible System Memory Allocation & Availability Adding PCI Cards Installing a PCI Expansion CardPCI Expansion Slots Serverboard Details Super H8DGU-F LayoutJumper Description Default Setting H8DGU-F Quick ReferenceConnector Definitions Power ConnectorsPwon Connector Reset ConnectorOverheat/Fan Fail LED OH Power On LEDNMI Button Universal Serial Bus Ports USB HeadersFan Headers Serial PortsUIO Power Connector LAN1/2 Ethernet PortsPower LED/Speaker Chassis IntrusionOverheat LED ATX PS/2 Keyboard and PS/2 Mouse PortsCompact Flash Card PWR Connector Video ConnectorUnit Identifier Button Cmos Clear Jumper SettingsTo Clear Cmos Watch Dog Enable/Disable LAN1/2 Enable/DisableVGA Enable/Disable I2C to PCI-Express SlotOnboard Indicators Power LEDLAN1/LAN2 LEDs Dedicated Ipmi LAN LEDsSata Drive Connections Sata PortsInstalling the OS/SATA Driver Enabling Sata RAIDSerial ATA Sata Building a Driver DisketteEnabling Sata RAID in the Bios Bios Setup ScreenUsing the DotHill and Adaptec RAID Utility DotHill RAID Utility Program ScreenInstalling Software Installing the RAID Driver During OS InstallationSuperDoctor SuperDoctor III Interface Display Screen Health Information Serverboard Battery 11. Installing the Onboard BatteryPage Page Control Panel System FansSystem Fan Failure Replacing System FansAccessing the Drive Bays Drive Bay Installation/RemovalRemoving the Front Bezel Hard Drive Installation Mounting a Hard Drive in a Drive CarrierInstalling/Removing a Hard Drive DVD-ROM Drive InstallationRemoving the Chassis Cover Power Supply Removing/Installing a DriveReplacing the Power Supply Removing/Replacing the Power SupplyIntroduction Main Menu Boot Feature Advanced Settings MenuSystem Time/System Date  Processor and Clock Options  Advanced Chipset Control  NorthBridge Configuration Bank Swizzle Mode ECC ModeDram ECC Enable Dram Timing Config IDE Configuration  Primary/Secondary/Third/Fourth IDE Master/SlavePIO Mode DMA ModeIDE Detect Timeout Sec A.R.T PCI/PnP Configuration  SuperIO Device Configuration Remote Access Configuration  Hardware Health Configuration  Acpi Configuration Set LAN Configuration  Ipmi Configuration View BMC System Event Log  Event Log Configuration Boot Menu  Boot Device PrioritySecurity Menu  Hard Disk DrivesExit Menu Appendix a Bios Error Beep Codes Amibios Error Beep CodesPage Appendix B Installing Windows Installing the Windows OS for a RAID SystemInstalling the Windows OS for a Non-RAID System Appendix C System Specifications Expansion Slots Regulatory Compliance