SUPER MICRO Computer 1022G-URF user manual Product Disposal, 製品の廃棄

Page 43

Chapter 4: Warning Statements for AC Systems

Attention

L'équipement doit être installé conformément aux normes électriques nationales et locales.

יצראה למשחה יקוח םואית

!הרהזא

.םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה תנקתה

ةقلعتملا ةيىطىلاو ةيلحملا هيواىقلل لثتمي نأ بجي ةيئابرهكلا تادعملا بيكرت ءابرهكلاب

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing

Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が あります。

警告

本产品的废弃处理应根据所有国家的法律和规章进行。

警告

本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.

4-15

Image 43
Contents Super + Server 1022G-URF Users Guide Introduction Server InstallationAbout This Manual Manual OrganizationAdvanced Chassis Setup Advanced Serverboard SetupBios Contents System Interface Advanced Serverboard Setup Appendix C System Specifications Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA Server Chassis Features Cooling System PCI Expansion SlotsFront Control Panel BackplaneAMD SR5670/SP5100 Chipset System Block Diagram Asia-Pacific Contacting SupermicroHeadquarters EuropeChoosing a Setup Location Preparing for SetupUnpacking the System Page Rack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Outer RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components Checking the Drives Checking the Drive Bay SetupChecking the Airflow Providing PowerControl Panel Buttons ResetInformational LED Status PowerControl Panel LEDs Information LEDNIC2 Hard Drive Carrier LEDs 警告の定義 この警告サインは危険を意味します。 人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、 About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Installation InstructionsCircuit Breaker 電源切断の警告 Power Disconnection Warningםיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל 機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Area電池の取り扱い Battery HandlingPage הדיחיה תא Redundant Power Suppliesバックプレーンの電圧 Backplane Voltage地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 Comply with Local and National Electrical Codes製品の廃棄 Product Disposalファン・ホットスワップの警告 Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 電源コードとACアダプター Power Cable and AC AdapterPage Page Chapter Advanced Serverboard Setup Installing the Processors Processor and Heatsink InstallationSocket, which may damage SNK-0042P Heatsink Installing a Passive CPU HeatsinkConnecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesI/O Ports Front Control Panel Header Pins JF1Top View of DDR3 Slot Installing MemoryInstalling Memory Modules Memory Support# Dimms CPU Dimm Population TablePossible System Memory Allocation & Availability Adding PCI Cards Installing a PCI Expansion CardPCI Expansion Slots Super H8DGU-F Layout Serverboard DetailsH8DGU-F Quick Reference Jumper Description Default SettingReset Connector Connector DefinitionsPower Connectors Pwon ConnectorOverheat/Fan Fail LED OH Power On LEDNMI Button Serial Ports Universal Serial Bus PortsUSB Headers Fan HeadersLAN1/2 Ethernet Ports UIO Power ConnectorATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerChassis Intrusion Overheat LEDCompact Flash Card PWR Connector Video ConnectorUnit Identifier Button Cmos Clear Jumper SettingsTo Clear Cmos I2C to PCI-Express Slot Watch Dog Enable/DisableLAN1/2 Enable/Disable VGA Enable/DisableDedicated Ipmi LAN LEDs Onboard IndicatorsPower LED LAN1/LAN2 LEDsSata Ports Sata Drive ConnectionsBuilding a Driver Diskette Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataBios Setup Screen Enabling Sata RAID in the BiosDotHill RAID Utility Program Screen Using the DotHill and Adaptec RAID UtilityInstalling the RAID Driver During OS Installation Installing SoftwareSuperDoctor SuperDoctor III Interface Display Screen Health Information 11. Installing the Onboard Battery Serverboard BatteryPage Page System Fans Control PanelReplacing System Fans System Fan FailureAccessing the Drive Bays Drive Bay Installation/RemovalRemoving the Front Bezel Mounting a Hard Drive in a Drive Carrier Hard Drive InstallationInstalling/Removing a Hard Drive DVD-ROM Drive InstallationRemoving the Chassis Cover Removing/Installing a Drive Power SupplyRemoving/Replacing the Power Supply Replacing the Power SupplyMain Menu Introduction Boot Feature Advanced Settings MenuSystem Time/System Date  Processor and Clock Options  Advanced Chipset Control  NorthBridge Configuration Dram Timing Config Bank Swizzle ModeECC Mode Dram ECC Enable Primary/Secondary/Third/Fourth IDE Master/Slave  IDE ConfigurationA.R.T PIO ModeDMA Mode IDE Detect Timeout Sec SuperIO Device Configuration  PCI/PnP Configuration Remote Access Configuration  Acpi Configuration  Hardware Health Configuration Set LAN Configuration  Ipmi Configuration View BMC System Event Log  Event Log Configuration  Hard Disk Drives Boot Menu Boot Device Priority Security MenuExit Menu Amibios Error Beep Codes Appendix a Bios Error Beep CodesPage Installing the Windows OS for a RAID System Appendix B Installing WindowsInstalling the Windows OS for a Non-RAID System Appendix C System Specifications Expansion Slots Regulatory Compliance