Raypak B6000 manual Wiring T-3

Page 5

WIRING T-3

1.Turn off power to the B6000 System Control Box.

2.Open front door of System Protocol Interface Gateway Enclosure.

3.Remove four screws and the lower cover, revealing the field wiring blocks.

4.Attach wires from interface card to the field wiring side of left terminal block (N+, N-, GND, NC). Refer to diagram in this user manual.

5.Open front door of the B6000 System Control Box.

6.Remove four screws and the lower cover, revealing the field wiring blocks in lower left.

7.Run RS-485 cable (provided) to the lower left field wiring terminal in the

B6000 System Control box. Attach wires to the upper four terminals as follows:

BLU/WHT

to

+

(1)

WHT/BLU

to

-

(2)

ORG/WHT

to

COM

(3)

SHIELD

to

GND

(4)

8.The EPROM (CPX.XNMn), in small black ESD box, must be installed in place of the current EPROM.

9.View the B6000 System Control Board picture on the next page. Note location of EPROM, U4.

10.Remove four screws holding upper panel with display screen and keypad. Carefully remove upper panel and turn over exposing B6000 System Control Board, (see next page).

11.Using ESD procedures carefully remove the EPROM from location U4.

12.Again using ESD procedures carefully install the EPROM labeled CPXXNM or CPXXM into location U4.

13.Re-assemble B6000 System Control Box.

14.Turn power on to B6000 System Control Box.

15.Connect 120 VAC (hot, Neutral, ground) to T-3 at right terminal block.

16.Re-assemble.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Installation and Operating Manual Table of Contents Raypak B6000 System Protocol Interface Contents Quantity Installation and Mounting Wiring T-3 B6000 System Control Board Check Your Power Source Page 11.0.T-3 Product Specifications Modbus Communications Command TypesCommand Error Checking Modbus Register Map Data IntegritySW1 Modbus Port Configuration Dip Switch ConfigurationIndicates Factory Setting 11.3.2 B6000 Communications 11.3.1.3 T-3 Jumper ConfigurationsFunction Address Slave Driver Code Command Range Comments Modbus CommandsModbus Error Codes Modbus Protocol SupportLED Indicators DiagnosticsTechnical Support ProSoft Support, Service and WarrantyService and Repair Limited Warranty Modbus Register Map Appendix aBoiler #1 Function Function Function Type DescriptionBit Boiler #3 Boiler #2Boiler #4 Boiler #5Boiler #8 Boiler #6Boiler #7 40070 TS Boiler Start Times Sec Boiler #1
Related manuals
Manual 51 pages 14.6 Kb

B6000 specifications

The Raypak B6000 is a high-efficiency boiler designed for residential and commercial heating applications. Known for its reliability and advanced features, the B6000 exemplifies Raypak's commitment to engineering excellence and innovative technology.

One of the standout attributes of the Raypak B6000 is its robust construction. The boiler is built with high-quality materials, ensuring durability and longevity in a variety of environments. It features a compact design, which allows for easy installation even in spaces with limited room. Moreover, it has a user-friendly interface that facilitates straightforward operation and maintenance, making it accessible for both homeowners and HVAC professionals.

The B6000 is equipped with advanced heating technologies that enhance its performance and efficiency. It utilizes a modulating burner system that adjusts the heat output based on the demand, ensuring optimal energy usage. This not only leads to lower energy bills but also contributes to a reduced carbon footprint, making the B6000 an environmentally friendly choice.

Another key feature of the Raypak B6000 is its stainless steel heat exchanger, which provides superior heat transfer and contributes to the boiler's overall efficiency. The heat exchanger is designed to withstand high temperatures and pressures, ensuring safety and reliability throughout its operation. Additionally, the B6000 offers multiple venting options, including direct venting and horizontal venting, providing flexibility in installation.

The B6000 also comes with integrated controls that allow users to easily monitor and adjust settings. These controls can enhance energy efficiency by accommodating varying heating needs throughout the day. Furthermore, the boiler is compatible with smart home systems, enabling remote operation and monitoring.

In terms of safety features, the Raypak B6000 is equipped with multiple safety sensors and shutoff systems to ensure safe operation. This includes automatic shutdown in case of malfunction, preventing potential hazards.

Overall, the Raypak B6000 is a top-tier boiler that combines efficiency, reliability, and advanced technology, making it a preferred choice for those seeking a dependable heating solution. It is suitable for various applications, from residential heating to larger commercial projects, further establishing its versatility in the market. Whether for new installations or replacements, the B6000 stands out as a reliable option for efficient heating solutions.
Top Page Image Contents