SMC Networks VDSL2 manual Connecting Fiber Optic Devices

Page 56

MAKING NETWORK CONNECTIONS

Connecting Fiber Optic Devices

An optional SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-ZX) can be used for a backbone connection to your Internet Service Provider, or for connecting to a high-speed server.

Each single-mode fiber port requires 9/125 micron single-mode fiber optic cable with an LC connector at both ends. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends. 1000BASE-SX/LX/ZX uses duplex fiber, operating at a frequency of 1310 nm for both transmit and receive signals.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Note: When selecting a fiber SFP device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP transceiver.

1.Remove and keep the LC port’s rubber cover. When not connected to a fiber cable, the rubber cover should be replaced to protect the optics.

2.Check that the fiber terminators are clean. You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty fiber terminators on fiber cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port.

4-6

Image 56

Contents TigerAccess EE Page TigerAccess EE Installation Guide Trademarks Limited Warranty SMC Networks, Inc Mason Irvine, CA Compliances FCC Class aFCC Part ViiViii CE Mark Declaration of Conformance for EMI and Safety EECIndustry Canada Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety CompliancePSE Alarm Power Cord Safety France and Peru onlyPower Cord Set Xii France et Pérou uniquementXiii Environmental Statement PurposeAudience Related PublicationsTable of Contents Making Network Connections XviAppendices XviiTables XviiiFigures XixFigures Chapter About Tigeraccess EE Switch OverviewAbout the Tigeraccess EE Switch Vdsl Technology Vdsl ApplicationSwitch Architecture Network Management OptionsDescription of Hardware RJ-21 Ports 1000BASE-T PortsOptional SFP Transceivers SFP SlotsManagement Port Port and System Status LEDs Console PortEthernet-over-VDSL CPE Optional Equipment System Status LEDs Condition StatusVdsl Features Key FeaturesPower Supply Socket Ethernet Connectivity Expandability System FeaturesManagement features include Application Examples Introduction to SwitchingChapter Network Planning Internet Connections Internet ConnectionsRemote Connections with Fiber Cable Making Vlan ConnectionsMaking Vlan Connections Application Notes Network Planning Installing the Switch Installing Additional Equipment Verifying Site RequirementInstalling Ethernet Cabling Equipment Checklist Package ContentsMounting Optional Rack-Mounting EquipmentAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting to a Power Source Power SocketConnecting to the Console Port Wiring Map for Serial CableWiring Map for Serial Cable Switch’s 8-Pin Null Modem PC’s 9-PinConnecting to the Console Port Installing the Switch Connecting RJ-21 Cables Chapter Making Network ConnectionsConnecting to the Punch-down Blocks Connecting to the Punch-down BlocksUsing Patch Panels Using Patch PanelsCabling Guidelines Connecting Twisted-Pair DevicesNetwork Wiring Connections Connecting to PCs, Servers, Hubs and Switches Customer Premises ConnectionsConnecting Fiber Optic Devices Connectivity Rules Making LC Port Connections1000BASE-T Cable Requirements Mbps Gigabit Ethernet Cable LengthsMaximum 1000BASE-T Gigabit Ethernet Cable Length Maximum 1000BASE-SX Gigabit Ethernet Cable LengthMbps Fast Ethernet Cable Lengths Mbps Ethernet Cable LengthsCable Labeling and Connection Records Appendix a Troubleshooting Diagnosing Switch IndicatorsTable A-1 Diagnosing Switch Indicators Symptom Possible Cause ActionFault is on In-Band Access Power and Cooling ProblemsInstallation Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin AssignmentsTable B-1 10/100BASE-TX MDI and MDI-X Port Pinouts Pin MDI Signal Name MDI-X Signal Name10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Table B-2 1000BASE-T MDI and MDI-X Port PinoutsCable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-TFiber Standards RJ-21 Port Pin Assignments Table B-4 RJ-21 Port Pin Assignments Vdsl Line connectorPins Circuit Table B-5 DB-9 Port Pin Assignments Console Port Pin AssignmentsDB-9 Port Pin Assignments Console Port to 9-Pin DTE Port on PC Console to 25-Pin DTE Port on PCTable B-6 Console Port to 9-Pin DTE Port on PC Table B-7 Console to 25-Pin DTE Port on PCAppendix C Specifications Physical CharacteristicsVdsl Specifications Band Plan Up to 6 bands PortsSwitching Database 8K MAC address entries LEDs WeightTemperature Power SupplySwitch Features Management FeaturesStandards CompliancesSafety Compliances Table D-1 TigerAccess EE Products and Accessories Product Number DescriptionOrdering Information Glossary Glossary-11000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Transmission Control Protocol/Internet Protocol TCP/IPUser Datagram Protocol UDP Very high data rate Digital Subscriber Line VdslGlossary-7 Virtual LAN VlanGlossary-8 Index Index-1Index-2 Index-3 SFPIndex-4 Page For Technical SUPPORT, Call