SMC Networks SMC2582W-B manual Changing the TCP/IP Settings of the Managing Computer

Page 13

Fig. 4. Connecting a managing computer and an SMC2582W-B via Ethernet.

You can use either a cross-over Ethernet cable (included in the package) or a switch/hub with 2 nor- mal Ethernet cables.

NOTE: One connector of the Ethernet cable must be plugged into the LAN/CONFIG Ethernet jack of the SMC2582W-B for configuration.

2.3.2. Changing the TCP/IP Settings of the Managing Computer

Use the Windows Network Control Panel Applet to change the TCP/IP settings of the managing computer, so that the IP address of the computer and the IP address of the SMC2582W-B are in the same IP subnet. Set the IP address of the computer to 192.168.2.xxx (the default IP address of the SMC2582W-B is 192.168.2.50) and the subnet mask to 255.255.255.0.

TIP: You can use SMC2582W-B Configuration Utility on the companion CD-ROM to scan for all the SMC2582W-Bs on the network. Double-click a scanned SMC2582W-B to launch the Web browser to manage the SMC2582W-B. Note that this utility does not discover the SMC2682W.

NOTE: On Windows 2000/XP, SMC2582W-B Configuration Utility can only be run by a user with administrator privilege.

NOTE: For some versions of Windows, the computer needs to be restarted for the changes of TCP/IP settings to take effect.

13

Image 13

Contents C 2 5 8 2 W B Trademarks CopyrightTesla FCC Radiation Exposure Statement Federal Communication Commission Interference StatementIndustry Canada Class B Wichtige Sicherheitshinweise Germany EC Conformance Declaration Class BEdificio Conata Page Introduction Features Ieee 802.11b Operational modesOverview Page Management LED Definitions To power outlet To power the SMC2582W-B by SMCPWR-INJ3 Power InjectorHang the SMC2582W-B on the screws Mounting the SMC2582W-B on a WallMounting the SMC2582W-B on a wall Preparing for ConfigurationChanging the TCP/IP Settings of the Managing Computer Entering the User Name and Password Configuring the SMC2582W-BStart Selecting an Operational ModeLowing table Operational modes vs. wireless link types Configuring Ieee 802.11 Settings Configuring TCP/IP SettingsSelect the corresponding Enabled check box Wireless Distribution System settings To enable a WDS linkSettings changes are highlighted in red Reviewing and Applying SettingsFix the alignment of the antenna on one side Deploying the SMC2582W-BOverview Using Web-Based ManagementMenu Structure Advanced. Advanced settings of the SMC2582W-B Save, Save & Restart, and Cancel CommandsManagement. UPnP, System Log, and Snmp settings Viewing Status Associated Wireless Clients Home and Refresh CommandsSystem Log Current Dhcp MappingsGeneral Operations Selecting an Operational Mode Managing Firmware Changing PasswordUpgrading Firmware by Http Configuration restore by HttpTrigger the firmware upgrade process by clicking Upgrade To restore configuration of the SMC2582W-B by HttpUpgrading Firmware by Tftp Choose Tftp as the Firmware management protocolBacking up and Restoring Configuration Settings by Tftp Choose Tftp as the Firmware management protocol Configuring TCP/IP Related Settings Addressing Resetting Configuration to Factory DefaultsStatic Dhcp Mappings Dhcp Server BasicBasic Ieee 802.11b communication settings Link Integrity Wireless Distribution SystemWireless Distribution System settings To enable a WDS link Network topology containing a loop SecurityPage MAC-address-based access control settings MAC-Address-Based Access ControlClick Download MAC ACL download settingsEthernet Type Filters Configuring Advanced Settings Packet FiltersIP Protocol Filters Management Basic TCP/UDP Port FiltersUPnP Snmp System log settingsPage Appendix a Default Settings Wireless Settings Problems Appendix B TroubleshootingTCP/IP Settings Problems Check the following firstPage SMC2582W-B Configuration Utility Other ProblemsContact our technical support representatives for repair Distances and Data RatesPage Syslog Event Logging LEDs Power Configuration and Management Web-browser TelnetWeight 80 lbs Storage Temperature SMCPWR-INJ3 Power InjectorPin Assignments and Polarity + 4/5 7/8 Output Voltage Storage HumidityFor Technical SUPPORT, Call

Related manuals

Manual 2 pages 61.05 Kb