SMC Networks SMC2582W-B manual Choose Tftp as the Firmware management protocol

Page 30

To back up configuration of the SMC2582W-B by TFTP:

1.Get a computer that will be used as a TFTP server and as a managing computer to trigger the backup process.

2.Connect the computer and one of the LAN Ethernet switch port with a normal Ethernet cable.

3.Configure the IP address of the computer so that the computer and the SMC2582W-B are in the same IP subnet.

4.On the computer, run the TFTP Server utility. Select the Accept write requestscheck box, and specify the folder to which the configuration settings of the SMC2582W-B will be saved.

5.On the computer, run a Web browser and click the General, Firmware Tools hyperlink.

6.Choose TFTP as the Firmware management protocol.

7.Within the Configuration Backup/Restore section, specify the IP address of the computer, which acts as a TFTP server. If you don’t know the IP address of the computer, open a Command Prompt, and type IpConfig, then press the Enter key.

8.Trigger the backup process by clicking Back Up. The SMC2582W-B’s configuration settings will be saved as “AaBbCcDdEeFf.hex” by the TFTP server, where “AaBbCcDdEeFf” is the SMC2582W- B’s MAC address. For example, if the SMC2582W-B’s MAC address is 00-01-02-33-44-55, the configuration backup file will be “000102334455.hex”.

NOTE: Remember to select the Accept write requests check box of TFTP Server.

To restore configuration of the SMC2582W-B by TFTP:

1.Get a computer that will be used as a TFTP server and as a managing computer to trigger the restoring process.

2.Connect the computer and one of the LAN Ethernet switch port with a normal Ethernet cable.

3.Configure the IP address of the computer so that the computer and the SMC2582W-B are in the same IP subnet.

4.On the computer, run the TFTP Server utility. And specify the folder in which the configuration backup file resides. A configuration backup file is named by the SMC2582W-B’s MAC address. For example, if the SMC2582W-B’s MAC address is 00-01-02-33-44-55, the configuration backup file should be “000102334455.hex”.

5.On the computer, run a Web browser and click the General, Firmware Tools hyperlink.

6.Choose TFTP as the Firmware management protocol.

7.Within the Configuration Backup/Restore section, specify the IP address of the computer, which acts as a TFTP server. If you don’t know the IP address of the computer, open a Command Prompt, and type IpConfig, then press the Enter key.

8.Trigger the restoring process by clicking Restore.The SMC2582W-B will then download the con figuration backup file from the TFTP server.

NOTE: Make sure the file is a valid configuration backup file for the SMC2582W-B.

TIP: If you want to remotely back up or restore configuration from the Internet, adjust

the Timeout and Max no. of retries settings of TFTP Server for remote TFTP configuration backup/restore to succeed.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents C 2 5 8 2 W B Copyright TrademarksTesla Federal Communication Commission Interference Statement FCC Radiation Exposure StatementIndustry Canada Class B EC Conformance Declaration Class B Wichtige Sicherheitshinweise GermanyEdificio Conata Page Features Ieee 802.11b Operational modes IntroductionOverview Page Management LED Definitions To power the SMC2582W-B by SMCPWR-INJ3 Power Injector To power outletMounting the SMC2582W-B on a Wall Hang the SMC2582W-B on the screwsPreparing for Configuration Mounting the SMC2582W-B on a wallChanging the TCP/IP Settings of the Managing Computer Configuring the SMC2582W-B Entering the User Name and PasswordSelecting an Operational Mode StartLowing table Operational modes vs. wireless link types Configuring TCP/IP Settings Configuring Ieee 802.11 SettingsWireless Distribution System settings To enable a WDS link Select the corresponding Enabled check boxReviewing and Applying Settings Settings changes are highlighted in redDeploying the SMC2582W-B Fix the alignment of the antenna on one sideUsing Web-Based Management OverviewMenu Structure Save, Save & Restart, and Cancel Commands Advanced. Advanced settings of the SMC2582W-BManagement. UPnP, System Log, and Snmp settings Home and Refresh Commands Viewing Status Associated Wireless ClientsCurrent Dhcp Mappings System LogGeneral Operations Selecting an Operational Mode Changing Password Managing FirmwareConfiguration restore by Http Upgrading Firmware by HttpUpgrading Firmware by Tftp To restore configuration of the SMC2582W-B by HttpTrigger the firmware upgrade process by clicking Upgrade Choose Tftp as the Firmware management protocolBacking up and Restoring Configuration Settings by Tftp Choose Tftp as the Firmware management protocol Resetting Configuration to Factory Defaults Configuring TCP/IP Related Settings AddressingDhcp Server Basic Static Dhcp MappingsBasic Ieee 802.11b communication settings Wireless Distribution System Link IntegrityWireless Distribution System settings To enable a WDS link Security Network topology containing a loopPage MAC-Address-Based Access Control MAC-address-based access control settingsMAC ACL download settings Click DownloadConfiguring Advanced Settings Packet Filters Ethernet Type FiltersIP Protocol Filters TCP/UDP Port Filters Management BasicUPnP System log settings SnmpPage Appendix a Default Settings TCP/IP Settings Problems Appendix B TroubleshootingWireless Settings Problems Check the following firstPage Other Problems SMC2582W-B Configuration UtilityDistances and Data Rates Contact our technical support representatives for repairPage Configuration and Management Web-browser Telnet Syslog Event Logging LEDs PowerWeight 80 lbs Pin Assignments and Polarity + 4/5 7/8 Output Voltage SMCPWR-INJ3 Power InjectorStorage Temperature Storage HumidityFor Technical SUPPORT, Call
Related manuals
Manual 2 pages 61.05 Kb
Top Page Image Contents