SMC Networks 48-Port manual Status LEDs, Led

Page 18

ABOUT THE TIGERSWITCH 10/100

Status LEDs

The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table.

Port and System Status LEDs

LED	Condition	Status

Power	On	Switch is receiving power.

RDP	On	Redundant power is on, and the RPU is in
		backup or active mode.

	Off	Redundant power is off or has failed.

Mgmt	On	Agent is operational.

RJ-45 Ports

Link	On Amber	Port has established a valid 10 Mbps
		connection.

	On Green	Port has established a valid 100 Mbps
		connection.

	Flashing	Port has been partitioned due to an
		abnormal network condition, or manually
		disabled.

Act*	On	Traffic is passing through the port.

FDX*	On	Port is operating at full duplex.

	Off	Port is operating at half duplex.

FC*	On	Flow control enabled.

* Use the Mode Select button to select the LED display mode.

1-4

Image 18

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aEC Conformance Declaration Class a Industry Canada Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceIii Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Installing the Switch Troubleshooting A-1Making Network Connections Ordering Information D-1 Glossary Index Specifications C-1Cables B-1 ViiViii Chapter About Tigerswitch 10/100 OverviewSwitch Architecture Rear PanelDescription of Hardware Management Options10BASE-T/100BASE-TX Ports SMC6948L2 Status LEDs LEDNetwork Management Module Network Management ModuleSpanning Tree Protocol VLANsMulticast Switching Optional Media Extender ModulesTraffic Priority Optional Redundant Power Unit SMCRPU150W Power Supply ReceptaclesFeatures and Benefits ConnectivityExpandability Performance ManagementIntroduction to Switching Chapter Network PlanningSample Applications Collapsed BackboneCentral Wiring Closet Central Wiring ClosetCollapsed Backbone Using Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsConnectivity Rules Mbps Gigabit Ethernet Collision DomainMaximum Fiber Optic Cable Distance for 1000BASE-SX SMC 3-2 Rule for Class II Repeaters Maximum Network Diameter Using RepeatersMbps Fast Ethernet Collision Domain SMC 2-1 Rule for Class I RepeatersMbps Ethernet Collision Domain SMC 5-4-3 RuleMaximum Ethernet Cable Distance Application Notes Network Planning Installing the Switch Selecting a SiteEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetConnecting to a Power Source Power ReceptacleConnecting Network Devices Chapter Making Network ConnectionsConnecting to PCs, Servers, Hubs and Switches 1. Making Twisted-Pair ConnectionsWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Making Network Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems InstallationIn-Band Access Troubleshooting Troubleshooting Specifications Appendix B CablesFigure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin AssignmentsStraight-Through Wiring 100BASE-TX/10BASE-T Pin AssignmentsCrossover Wiring Console Port Pin Assignments Figure B-2. DB-9 Console Port Pin NumbersDB-9 Port Pin Assignments Console Port to 9-Pin COM Port on PCConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical CharacteristicsPower Supply WeightTemperature Power ConsumptionSwitch Features Management Features Compliances SafetyStandards EmissionsWarranty 1000BASE-SX Extender Module Slide-in Module100BASE-FX Extender Module ModelSMC6948NMM Appendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 BandwidthGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 See RPUIndex-4 Page Internet