SMC Networks 48-Port manual Compliances, FCC Class a, EC Conformance Declaration Class a

Page 7

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater for 10 Mbps connections and Category 5 for 100 Mbps connections. Use 50/125 or 62.5/125 micron multimode fiber optic cable for SC or ST-type connections.

Warnings 1. Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.

2.When connecting this hub to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

EC Conformance Declaration - Class A

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí,

Barcelona, Spain.

This information technology equipment complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the CE Mark accordingly. It conforms to the following specifications:

EMC: EN55022 (1988)/CISPR-22 (1995) Class A

IEC 1000-4-2	4 kV CD, 8 kV AD
IEC 1000-4-3 (1995)	3	V/m
IEC 1000-4-4 (1995)	1.0 kV - (power line)
	0.5 kV - (signal line)
IEC 1000-4-6 (1995)	3	Vrms

i

Image 7

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesEC Conformance Declaration Class a Industry Canada Class a Underwriters Laboratories Compliance Statement Safety ComplianceIii Warnhinweis Faseroptikanschlüsse Optische SicherheitWichtige Sicherheitshinweise Germany Table of Contents Troubleshooting A-1 Installing the SwitchMaking Network Connections Vii Specifications C-1Cables B-1 Ordering Information D-1 Glossary IndexViii Overview Chapter About Tigerswitch 10/100Rear Panel Switch ArchitectureManagement Options Description of Hardware10BASE-T/100BASE-TX Ports SMC6948L2 LED Status LEDsNetwork Management Module Network Management ModuleVLANs Spanning Tree ProtocolOptional Media Extender Modules Multicast SwitchingTraffic Priority Power Supply Receptacles Optional Redundant Power Unit SMCRPU150WConnectivity Features and BenefitsExpandability Management PerformanceChapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsCentral Wiring Closet Central Wiring ClosetRemote Connections with Fiber Cable Collapsed Backbone Using Fiber CableMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX SMC 2-1 Rule for Class I Repeaters Maximum Network Diameter Using RepeatersMbps Fast Ethernet Collision Domain SMC 3-2 Rule for Class II RepeatersSMC 5-4-3 Rule Mbps Ethernet Collision DomainMaximum Ethernet Cable Distance Application Notes Network Planning Selecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceChapter Making Network Connections Connecting Network Devices1. Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Making Network Connections Diagnosing Switch Indicators Appendix a TroubleshootingInstallation Power and Cooling ProblemsIn-Band Access Troubleshooting Troubleshooting Appendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers100BASE-TX/10BASE-T Pin Assignments Straight-Through WiringCrossover Wiring Figure B-2. DB-9 Console Port Pin Numbers Console Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC DB-9 Port Pin AssignmentsConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsPower Consumption WeightTemperature Power SupplySwitch Features Management Features Emissions SafetyStandards CompliancesWarranty Model Slide-in Module100BASE-FX Extender Module 1000BASE-SX Extender ModuleSMC6948NMM Appendix D Ordering Information Ordering Information Bandwidth GlossaryGlossary-1 Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index-1 IndexIndex-2 See RPU Index-3Index-4 Page Internet