SMC Networks 48-Port manual Connecting to a Power Source, Power Receptacle

Page 40

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the receptacle located at the back of the device.

Figure 3-4. Power Receptacle

2. Plug the other end of the cable into a grounded, 3-pin socket.

Note: For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is lit. If not, check that the power cable is correctly plugged in. The Mgmt LED on the switch will be lit.

4.If you have a purchased Redundant Power Unit, connect it to the device and to an AC power source now, following the instructions included with the package.

3-6

Image 40

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesEC Conformance Declaration Class a Industry Canada Class a Safety Compliance IiiWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Troubleshooting A-1 Installing the SwitchMaking Network Connections Specifications C-1 Cables B-1Ordering Information D-1 Glossary Index ViiViii Chapter About Tigerswitch 10/100 OverviewSwitch Architecture Rear PanelManagement Options Description of Hardware10BASE-T/100BASE-TX Ports SMC6948L2 Status LEDs LEDNetwork Management Module Network Management ModuleSpanning Tree Protocol VLANsOptional Media Extender Modules Multicast SwitchingTraffic Priority Optional Redundant Power Unit SMCRPU150W Power Supply ReceptaclesConnectivity Features and BenefitsExpandability Performance ManagementIntroduction to Switching Chapter Network PlanningSample Applications Collapsed BackboneCentral Wiring Closet Central Wiring ClosetCollapsed Backbone Using Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX Maximum Network Diameter Using Repeaters Mbps Fast Ethernet Collision DomainSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I RepeatersSMC 5-4-3 Rule Mbps Ethernet Collision DomainMaximum Ethernet Cable Distance Application Notes Network Planning Installing the Switch Selecting a SitePackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetConnecting to a Power Source Power ReceptacleConnecting Network Devices Chapter Making Network ConnectionsConnecting to PCs, Servers, Hubs and Switches 1. Making Twisted-Pair ConnectionsWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Making Network Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsInstallation Power and Cooling ProblemsIn-Band Access Troubleshooting Troubleshooting Specifications Appendix B CablesFigure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin AssignmentsStraight-Through Wiring 100BASE-TX/10BASE-T Pin AssignmentsCrossover Wiring Console Port Pin Assignments Figure B-2. DB-9 Console Port Pin NumbersConsole Port to 9-Pin COM Port on PC DB-9 Port Pin AssignmentsConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical CharacteristicsWeight TemperaturePower Supply Power ConsumptionSwitch Features Management Features Safety StandardsCompliances EmissionsWarranty Slide-in Module 100BASE-FX Extender Module1000BASE-SX Extender Module ModelSMC6948NMM Appendix D Ordering Information Ordering Information Glossary Glossary-1Auto-Negotiation BandwidthGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 See RPUIndex-4 Page Internet