Seagate ST1000NM0033 manual Installation, Drive Orientation, Cooling

Page 50

10.0INSTALLATION

Constellation ES.3 disk drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

SAS drives are designed to be attached to the host system without I/O or power cables. If you NOTE intend the use the drive in a non-backplane host system, connecting the drive using high-quality

cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 11.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 17. Physical interface

NOTE

Image is for reference only, may not represent actual drive.

10.1DRIVE ORIENTATION

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two preferred mounting orientations.

10.2COOLING

Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 6.5.1, "Temperature."

The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disk assembly (HDA). You should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 6.5.1.

Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 6.5.1 in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources within the rack, cabinet, or drawer environment.

CONSTELLATION ES.3 SAS PRODUCT MANUAL, REV. B

45

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Constellation ES.3 SAS Document Revision History Contents Installation Contents Seagate Technology Support Services Scope SEDApplicable Standards and Reference Documentation StandardsTaiwanese Bsmi Australian C-TickKorean KCC European Union Restriction of Hazardous Substances RoHSChina Restriction of Hazardous Substances RoHS Directive Reference DocumentsGeneral Description Performance Standard FeaturesMedia Description Formatted Capacities FACTORY-INSTALLED OptionsReliability Programmable Drive CapacityFormat command execution time for 512-byte sectors minutes Performance CharacteristicsInternal Drive Characteristics General performance characteristicsCache Operation START/STOP TimePREFETCH/MULTI-SEGMENTED Cache Control Caching write data Prefetch operationReliability and Service Reliability SpecificationsError Rates Hot plugging the drive 3 S.M.A.R.TReporting control Controlling S.M.A.R.TPerformance impact Determining rateDST failure definition State of the drive prior to testingDrive Self Test DST ImplementationShort test Function Code 001b Invoking DSTShort and extended tests Extended test Function Code 010bStorage Product warrantyShipping Product repair and return informationPowerChoice modes PHYSICAL/ELECTRICAL SpecificationsPowerchoicetm Power Management AC Power Requirements DC Power Requirements4TB drive DC power requirements 3TB drive DC power requirements 2TB drive DC power requirements 1TB drive DC power requirements Conducted noise immunity General DC power requirement notesPower sequencing Current profiles TB model current profilesTB model current profiles TB model current profiles TB model current profiles 4TB models in 6Gb operation Power Dissipation4TB models in 3Gb operation 3TB models in 3Gb operation 3TB models in 6Gb operation2TB models in 3Gb operation 2TB models in 6Gb operation1TB models in 3Gb operation 1TB models in 6Gb operationImage is for reference only, may not represent actual drive Temperature a. OperatingEnvironmental Limits Relative humidityShock and vibration ShockRecommended mounting Acoustics Air cleanlinessVibration Corrosive environmentMechanical Specifications 1TBSeagate Enterprise SED PurposeValidation Program Security LevelData Encryption Controlled AccessAbout SELF-ENCRYPTING Drives Random Number Generator RNGSupported Commands Authenticated Firmware DownloadPower Requirements Data BandsDrive Error Recovery Procedures Defect and Error ManagementDrive Internal DEFECTS/ERRORS SAS System Errors Background Media ScanIdle Read After Write Media PRE-SCANDeferred AUTO-REALLOCATION Protection Information PISetting and determining the current Type Level Identifying a Protection Information driveCooling InstallationDrive Orientation Drive Mounting X = F 15lb = 67NGrounding Task management functions SAS FeaturesInterface Requirements Task management responsesScsi Commands Supported Supported commands Supported commands Supported commands Inquiry data Constellation ES.3 inquiry dataMode Sense data Block Descriptor CHG 9C 0A 9D 0F FF FF FF FF FF FF FF FF DEF 12 1400 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 Miscellaneous Operating Features and Conditions Miscellaneous featuresSAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers PowerSignal Characteristics Ready LED OutAdditional Information Differential signalsSAS-2 Specification Compliance Index Page KCC See also cooling Page Seagate Technology LLC
Related manuals
Manual 52 pages 18.94 Kb

ST1000NM0033 specifications

The Seagate ST1000NM0033 is a high-performance hard disk drive (HDD) designed specifically for enterprise applications. With a storage capacity of 1TB, it offers a balance of performance, reliability, and efficiency, making it suitable for data centers, cloud storage, and server environments. Built with Seagate's robust engineering, the ST1000NM0033 is ideal for handling heavy workloads and intensive data processes.

One of the standout features of this HDD is its rotational speed of 7200 RPM. This speed allows for quick data access and fast read/write operations, which is essential for data-intensive applications. The drive is equipped with 64MB of cache, further enhancing its efficiency by speeding up data retrieval for frequently accessed files.

Another key characteristic of the ST1000NM0033 is its SATA interface, which typically facilitates high-bandwidth data transfer rates. With a sustained data transfer rate of up to 160 MB/s, it ensures that large files, such as videos and databases, can be transferred swiftly, minimizing downtime and improving overall system performance.

The drive's durability is backed by Seagate’s Advanced Format technology, which enhances the format compatibility, storage efficiency, and reliability of the drive through improved error correction. With a mean time between failures (MTBF) rating of 1 million hours, users can trust the STA0033 to provide exceptional longevity and stability, critical in enterprise environments where data integrity is paramount.

Furthermore, the ST1000NM0033 supports various workload types due to its design optimized for multi-user environments. The drive can handle up to 180TB/year workload rate, making it capable of supporting applications with high data demand.

Environmentally, Seagate ensures that this model is energy efficient, contributing to reduced power consumption in enterprise settings. The drive operates effectively within a specified temperature range, ensuring that it remains operational under different environmental conditions.

In summary, the Seagate ST1000NM0033 is an excellent choice for businesses seeking a reliable, high-capacity HDD with robust performance features. Its combination of speed, efficiency, durability, and capacity positions it as a strong contender in the enterprise storage solutions market. With its extensive feature set, it continues to cater to the demanding needs of modern data centers and enterprise applications.
Top Page Image Contents