Seagate ST1000NM0033 manual Drive Mounting, X = F 15lb = 67N

Page 51

If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 18. The air-flow patterns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guidelines of Section 6.5.1 are met.

Ab

ote A l

b

 

b

Ab

ote A l

Figure 18. Air flow

NOTE

Image is for reference only, may not represent actual drive.

10.3DRIVE MOUNTING

Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.

The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiffness:

K x X = F < 15lb = 67N

where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

NOTE Do not cover breather hole on top cover.

Breather Hole

Do Not

Cover

Breather hole location - top cover

CONSTELLATION ES.3 SAS PRODUCT MANUAL, REV. B

46

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Constellation ES.3 SAS Document Revision History Contents Installation Contents Seagate Technology Support Services SED ScopeStandards Applicable Standards and Reference DocumentationEuropean Union Restriction of Hazardous Substances RoHS Australian C-TickKorean KCC Taiwanese BsmiReference Documents China Restriction of Hazardous Substances RoHS DirectiveGeneral Description Standard Features Media DescriptionPerformance Programmable Drive Capacity FACTORY-INSTALLED OptionsReliability Formatted CapacitiesGeneral performance characteristics Performance CharacteristicsInternal Drive Characteristics Format command execution time for 512-byte sectors minutesSTART/STOP Time PREFETCH/MULTI-SEGMENTED Cache ControlCache Operation Prefetch operation Caching write dataReliability Specifications Error RatesReliability and Service 3 S.M.A.R.T Hot plugging the driveDetermining rate Controlling S.M.A.R.TPerformance impact Reporting controlImplementation State of the drive prior to testingDrive Self Test DST DST failure definitionExtended test Function Code 010b Invoking DSTShort and extended tests Short test Function Code 001bProduct repair and return information Product warrantyShipping StoragePHYSICAL/ELECTRICAL Specifications Powerchoicetm Power ManagementPowerChoice modes DC Power Requirements AC Power Requirements4TB drive DC power requirements 3TB drive DC power requirements 2TB drive DC power requirements 1TB drive DC power requirements General DC power requirement notes Power sequencingConducted noise immunity TB model current profiles Current profilesTB model current profiles TB model current profiles TB model current profiles Power Dissipation 4TB models in 3Gb operation4TB models in 6Gb operation 3TB models in 6Gb operation 3TB models in 3Gb operation2TB models in 6Gb operation 2TB models in 3Gb operation1TB models in 6Gb operation 1TB models in 3Gb operationRelative humidity Temperature a. OperatingEnvironmental Limits Image is for reference only, may not represent actual driveShock Shock and vibrationRecommended mounting Corrosive environment Air cleanlinessVibration Acoustics1TB Mechanical SpecificationsSecurity Level PurposeValidation Program Seagate Enterprise SEDRandom Number Generator RNG Controlled AccessAbout SELF-ENCRYPTING Drives Data EncryptionData Bands Authenticated Firmware DownloadPower Requirements Supported CommandsDefect and Error Management Drive Internal DEFECTS/ERRORSDrive Error Recovery Procedures Background Media Scan SAS System ErrorsProtection Information PI Media PRE-SCANDeferred AUTO-REALLOCATION Idle Read After WriteIdentifying a Protection Information drive Setting and determining the current Type LevelInstallation Drive OrientationCooling X = F 15lb = 67N Drive MountingGrounding Task management responses SAS FeaturesInterface Requirements Task management functionsScsi Commands Supported Supported commands Supported commands Supported commands Constellation ES.3 inquiry data Inquiry dataMode Sense data Block Descriptor CHG 9C 0A 9D 0F FF FF FF FF FF FF FF FF DEF 12 1400 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 Miscellaneous features Miscellaneous Operating Features and ConditionsSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out PowerSignal Characteristics SAS transmitters and receiversDifferential signals SAS-2 Specification ComplianceAdditional Information Index Page KCC See also cooling Page Seagate Technology LLC
Related manuals
Manual 52 pages 18.94 Kb

ST1000NM0033 specifications

The Seagate ST1000NM0033 is a high-performance hard disk drive (HDD) designed specifically for enterprise applications. With a storage capacity of 1TB, it offers a balance of performance, reliability, and efficiency, making it suitable for data centers, cloud storage, and server environments. Built with Seagate's robust engineering, the ST1000NM0033 is ideal for handling heavy workloads and intensive data processes.

One of the standout features of this HDD is its rotational speed of 7200 RPM. This speed allows for quick data access and fast read/write operations, which is essential for data-intensive applications. The drive is equipped with 64MB of cache, further enhancing its efficiency by speeding up data retrieval for frequently accessed files.

Another key characteristic of the ST1000NM0033 is its SATA interface, which typically facilitates high-bandwidth data transfer rates. With a sustained data transfer rate of up to 160 MB/s, it ensures that large files, such as videos and databases, can be transferred swiftly, minimizing downtime and improving overall system performance.

The drive's durability is backed by Seagate’s Advanced Format technology, which enhances the format compatibility, storage efficiency, and reliability of the drive through improved error correction. With a mean time between failures (MTBF) rating of 1 million hours, users can trust the STA0033 to provide exceptional longevity and stability, critical in enterprise environments where data integrity is paramount.

Furthermore, the ST1000NM0033 supports various workload types due to its design optimized for multi-user environments. The drive can handle up to 180TB/year workload rate, making it capable of supporting applications with high data demand.

Environmentally, Seagate ensures that this model is energy efficient, contributing to reduced power consumption in enterprise settings. The drive operates effectively within a specified temperature range, ensuring that it remains operational under different environmental conditions.

In summary, the Seagate ST1000NM0033 is an excellent choice for businesses seeking a reliable, high-capacity HDD with robust performance features. Its combination of speed, efficiency, durability, and capacity positions it as a strong contender in the enterprise storage solutions market. With its extensive feature set, it continues to cater to the demanding needs of modern data centers and enterprise applications.
Top Page Image Contents