Seagate U Series 9 CE manual Jumper settings, Master/slave configuration, Cable-select option

Page 27

3.3Jumper settings

3.3.1Master/slave configuration

The options jumper block shown in Figure 1 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA- compatible slave

Cable select

Limit drive capacity to 32 Gbytes

7 5 3 1

8 6 4 2

Circuit Board

Figure 1. Master/slave jumper settings

3.3.2Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 1. Refer to your computer manual to determine whether your computer supports this option.

3.3.3Alternate capacity jumper

Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32 Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the full capacity of the drive, you can:

•Update the BIOS

•Use third-party software such as DiscWizard™ or Disk Manager

•Use a third-party host adapter

For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcom- mand “F1H Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity. See Section 4.1.3 on page 28 for more details on the Set Features command.

U Series 9 ce Product Manual, Rev. F

17

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Series 9 ce Page Series 9 ce Page Revision status summary sheet Page Contents Series 9 ce Product Manual, Rev. F List of Figures Viii Series 9 ce Product Manual, Rev. F Introduction Series 9 ce Product Manual, Rev. F Specification summary table Drive specificationsSeries 9 ce Product Manual, Rev. F Physical organization Default logical geometryLBA mode Formatted capacityStart/stop times Physical characteristicsPower specifications Seek timeRead/write power and current Power consumptionSpinup power Seek modeTypical 5V startup and operation current profile Typical current profileSleep mode Power-management modesActive mode Idle modeEnvironmental specifications Acoustics Electromagnetic immunity ReliabilityFluid Dynamic Bearing FDB motor acoustics Agency certification Page Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsCable-select option Jumper settingsMaster/slave configuration Drive as master with a non-ATA-compatible slaveUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view Series 9 ce Product Manual, Rev. F ATA interface ATA interface signals and connector pinsO pins and supported ATA signals Command name Command code in hex ATA-standard commands Supported ATA commandsCommand name Command code in hex Word Description Value Identify Device commandXx07H Description if bit is set to Bit Word 0CH Set Features commandCode in features Register A.R.T. command 4 S.M.A.R.T. commandsSeries 9 ce Product Manual, Rev. F Technical Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Presales SupportAuthorized Service Centers Warranty ServiceCall Center Toll-free Direct dial FAX / Internet Call Center Toll-free Direct dialAmericas +1-405-324-47301 +1-405-324-4704 Americas SEAGATE2 +1-405-324-47003 +1-405-324-4702FAX Services-All Europe toll call Call Center Presales and Technical Support Warranty ServiceToll-Free Support Numbers Asia/Pacific Support Services Series 9 ce Product Manual, Rev. F Numerics IndexPage Page Series 9 ce Product Manual, Rev. F Page Seagate Technology LLC

U Series 9 CE specifications

The Seagate U Series 9 CE (Consumer Electronics) is a robust external storage solution designed to meet the growing demands of consumers for reliable, high-capacity data storage. This portable hard drive boasts a combination of innovative technology, user-friendly features, and an appealing design, making it an excellent choice for multimedia enthusiasts and professionals alike.

One of the standout features of the Seagate U Series 9 CE is its impressive storage capacity options. Ranging from 1TB to 5TB, users have the flexibility to choose a size that suits their specific needs. This vast storage capability allows users to carry their entire media library, including photos, videos, music, and documents, all in one compact device.

The U Series 9 CE is equipped with USB 3.0 technology, offering high data transfer speeds that significantly reduce wait times when transferring large files. This backward-compatible interface ensures that users can connect to a wide array of devices, including laptops, desktops, and gaming consoles, without any hassle. The drive’s plug-and-play functionality further enhances the user experience, as it requires no additional software installation.

In terms of design, the Seagate U Series 9 CE is sleek and portable, featuring a lightweight chassis that easily fits into a backpack or purse. Its minimalist aesthetic comes in various color options, allowing users to choose a drive that reflects their personal style.

Security is a priority for any storage device, and the U Series 9 CE incorporates features to protect data. With software encryption options available, users can safeguard their sensitive information from unauthorized access. Additionally, the drive has been designed for durability, with protection against shock and vibration, ensuring that valuable data remains safe even in demanding conditions.

Lastly, Seagate backs the U Series 9 CE with a warranty, providing users with peace of mind regarding their investment. Overall, the Seagate U Series 9 CE stands out as a top-tier external hard drive that combines performance, portability, and security, making it an ideal choice for anyone seeking reliable digital storage solutions.
Top Page Image Contents