Seagate ST94813AS, ST98823AS, ST96812AS Reliability, Agency certification, Safety certification

Page 20

2.13

Reliability

 

 

 

Measurement type

Specification

 

 

Nonrecoverable read errors

1 per 1014 bits read, max.

Mean time between failures

330,000 power-on hours

 

 

At nominal power, 25°C ambient temperature.

 

 

Max case temperature: 65°C at the case measurement location shown in Figure

 

 

5.

 

 

Load/Unload (U/UL)

 

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

 

 

20,000 hard power on/off cycles

32°C, 80% relative humidity

600,000 software-controlled power on/off cycles

5°C, 80% relative humidity

20,000 hard power on/off cycles

5°C, 10% relative humidity

 

55°C, 16% relative humidity

 

 

 

Service Life

5 years

 

 

 

Warranty

 

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to access the

 

 

following web page:

 

 

www.seagate.com/support/service/

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

 

 

vide the drive serial number, model number (or part number) and country of pur-

 

 

chase. The system will display the warranty information for your drive.

 

 

 

2.14Agency certification

2.14.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.

2.14.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

14

Momentus 5400.2 SATA Product Manual, Rev. C

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Momentus 5400.2 Sata Page Contents Momentus 5400.2 Sata Product Manual, Rev. C List of Figures Page Introduction Momentus 5400.2 Sata disc driveAbout the Serial ATA interface Drive specifications Specification summary tableWarranty information for your drive Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Drive specificationPhysical organization Recording and interface technologySeek time Start/stop timesTypical seek times Typical seek times msec Read WritePower specifications Deferred spinup Additional detailsPower-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Radio frequency environmentsSafety certification Measurement type SpecificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingMomentus 5400.2 Sata Product Manual, Rev. C Serial ATA connector pin definitions SignalSerial ATA Sata interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsMomentus 5400.2 Sata Product Manual, Rev. C Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Set Features command valuesCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Seagate Technology support services InternetPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE Sata Momentus 5400.2 Sata Product Manual, Rev. C Page Seagate Technology LLC
Top Page Image Contents