Seagate ST98823AS, ST96812AS, ST94813AS Configuring the drive, Serial ATA cables and connectors

Page 24

3.2Configuring the drive

Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation with no jumpers, terminators, or other settings. It is not nec- essary to set any jumpers on this drive for proper operation. The jumper block adjacent to the signal connector is for factory use only.

SATA interface connector

Jumper block SATA power connector (factory use only)

Figure 3. Serial ATA connectors

3.3Serial ATA cables and connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec- tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 7 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 4.

SATA interface connector

Power connector

SATA interface cable

Power cable

Figure 4. Attaching SATA cabling

Each cable is keyed to ensure correct orientation.

18

Momentus 5400.2 SATA Product Manual, Rev. C

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Momentus 5400.2 Sata Page Contents Momentus 5400.2 Sata Product Manual, Rev. C List of Figures Page Introduction Momentus 5400.2 Sata disc driveAbout the Serial ATA interface Drive specifications Specification summary tableWarranty information for your drive Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Drive specificationPhysical organization Recording and interface technologySeek time Start/stop timesTypical seek times Typical seek times msec Read WritePower specifications Deferred spinup Additional detailsPower-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Radio frequency environmentsSafety certification Measurement type SpecificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingMomentus 5400.2 Sata Product Manual, Rev. C Serial ATA connector pin definitions SignalSerial ATA Sata interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsMomentus 5400.2 Sata Product Manual, Rev. C Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Set Features command values3 S.M.A.R.T. commands A.R.T. commandsCode in features register A.R.T. command Seagate Technology support services InternetPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index ITE Sata Momentus 5400.2 Sata Product Manual, Rev. C Page Seagate Technology LLC
Top Page Image Contents