Seagate ST98823AS, ST96812AS manual 3 S.M.A.R.T. commands, Code in features register A.R.T. command

Page 36

4.3.3S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni- tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-5 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that elimi- nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 9:

S.M.A.R.T. commands

 

 

Code in features register

S.M.A.R.T. command

 

 

 

D0H

 

S.M.A.R.T. Read Data

 

 

 

D1H

 

Vendor-specific

 

 

 

D2H

 

S.M.A.R.T. Enable/Disable Attribute Autosave

 

 

 

D3H

 

S.M.A.R.T. Save Attribute Values

 

 

 

D4H

 

S.M.A.R.T. Execute Off-line Immediate (runs DST)

 

 

 

D5H

 

S.M.A.R.T. Read Log Sector

 

 

 

D6H

 

S.M.A.R.T. Write Log Sector

 

 

 

D7H

 

Vendor-specific

 

 

 

D8H

 

S.M.A.R.T. Enable Operations

 

 

 

D9H

 

S.M.A.R.T. Disable Operations

 

 

 

DAH

 

S.M.A.R.T. Return Status

 

 

 

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

30

Momentus 5400.2 SATA Product Manual, Rev. C

Image 36
Contents Momentus 5400.2 Sata Page Contents Momentus 5400.2 Sata Product Manual, Rev. C List of Figures Page Introduction Momentus 5400.2 Sata disc driveAbout the Serial ATA interface Drive specifications Specification summary tableWarranty information for your drive Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Drive specificationPhysical organization Recording and interface technologySeek time Start/stop timesTypical seek times Typical seek times msec Read WritePower specifications Deferred spinup Additional detailsPower-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Radio frequency environmentsSafety certification Measurement type SpecificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingMomentus 5400.2 Sata Product Manual, Rev. C Serial ATA connector pin definitions SignalSerial ATA Sata interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsMomentus 5400.2 Sata Product Manual, Rev. C Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Set Features command values3 S.M.A.R.T. commands A.R.T. commandsCode in features register A.R.T. command Seagate Technology support services InternetPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index ITE Sata Momentus 5400.2 Sata Product Manual, Rev. C Page Seagate Technology LLC