Seagate ST96812AS, ST98823AS, ST94813AS Drive mounting, Mounting dimensions-top, side and end view

Page 25

3.4Drive mounting

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 5 for drive mounting dimensions. Follow these important mounting precautions when mount- ing the drive:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only M3 UNC mounting screws.

•Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).

•Four (4) threads (0.080 inches) minimum screw engagement recommended.

Measurements shown in Figure 5 are in inches.

2 .399

COF CONN. DATUM B

C OF DRIVE

( .189 )

2

SATA

( .020 )

SECTION B-B (SATA)

.039 B C D

2 .152

.399

2

DETAIL A (PATA)

B

.039 B C D

.016 C

2 .012

.370

2

DETAIL A (SATA)

1DIMENSIONS PER EIA-720 OR SFF 8201 SPECIFICATION.

2DIMENSIONS PER SFF 8212 OR SFF 8223.

3DRIVE LENGTH W/ PATA IS 3.945±.057 (WORST CASE). DRIVE LENGTH W/ SATA IS 3.957±.062 (WORST CASE).

3.945 ± .010 (BASE)

.157 2

1 2.750 ±.010

(BASE)

PATA			3
BASE			1
			3.567
	.551	1

.374 ±.008

-D-

2X .118 BOTH SIDES

1

BASE	3.567
	(BASE) 1

.551

1

B

DETAIL A

( .490 )

.217 ±.050

.217 ±.050

( .673 )

2X M3 X 0.5-6H

MOUNTING HOLES; BOTH SIDES

.12 MIN FULL THREAD

0.148 ±.010 X 90

1

4X M3 X 0.5-6H

MOUNTING HOLES; BOTH SIDES

.10 MIN FULL THREAD 0.148 ±.010 X 90

1

1

2.430

-B-

.160 1

-C-

Figure 5. Mounting dimensions—top, side and end view

Momentus 5400.2 SATA Product Manual, Rev. C

19

Image 25

Contents Momentus 5400.2 Sata Page Contents Momentus 5400.2 Sata Product Manual, Rev. C List of Figures Page Momentus 5400.2 Sata disc drive IntroductionAbout the Serial ATA interface Specification summary table Drive specificationsWarranty information for your drive LBA mode Default logical geometryFormatted capacity Cylinders Read/write heads Sectors per track 16,383Drive specification Physical characteristicsPhysical organization Recording and interface technologyStart/stop times Seek timeTypical seek times Typical seek times msec Read WritePower specifications Additional details Deferred spinupPower management modes Power-management modesActive mode Idle modeEnvironmental specifications Operating shock ShockNonoperating shock VibrationElectromagnetic immunity AcousticsDrive level acoustics Radio frequency environmentsMeasurement type Specification Safety certificationReliability Agency certificationAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensions-top, side and end viewMomentus 5400.2 Sata Product Manual, Rev. C Signal Serial ATA connector pin definitionsSerial ATA Sata interface Segment Pin Function DefinitionP10 Ground 2nd mate P11 Reserved Pin Function DefinitionCommand name Command code in hex ATA-standard commands Supported ATA commandsATA-standard security commands Command name Command code in hexMomentus 5400.2 Sata Product Manual, Rev. C Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordSet Features command values Set Features commandA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Internet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index ITE Sata Momentus 5400.2 Sata Product Manual, Rev. C Page Seagate Technology LLC