Seagate ST936751SS, ST973451SS manual Environmental limits, Temperature, Relative humidity

Page 37

6.4Environmental limits

Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C).

6.4.1Temperature

a.Operating

With cooling designed to maintain the case temperatures, the drive meets all specifications over a 41°F to 131°F (5°C to 55°C) drive ambient temperature range with a maximum temperature gradient of 36°F (20°C) per hour. The enclosure for the drive should be designed such that these temperatures not exceeded. Air flow may be needed to achieve these temperature values (see Section 8.2). Operation at case tempera- tures above these values may adversely affect the drives ability to meet specifications.

The MTBF specification for the drive is based on operating in an environment that ensures that the case temperatures are not exceeded. Occasional excursions to drive ambient temperatures of 131°F (55°C) or 41°F (5°C) may occur without impact to specified MTBF. Air flow may be needed to achieve these tempera- tures. Continual or sustained operation at case temperatures above these values may degrade MTBF. The maximum allowable continuous or sustained HDA case temperature for the rated MTBF is 122°F (50°C).

To confirm that the required cooling for the electronics and HDA is provided, place the drive in its final mechanical configuration, perform random write/read operations. After the temperatures stabilize, measure the case temperature of the drive.

The maximum allowable HDA case temperature is 60°C. Operation of the drive at the maximum case tem- perature is intended for short time periods only. Continuous operation at the elevated temperatures will reduce product reliability.

b.Non-operating

–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive.

HDA Temp.

Check Point

Figure 7. Location of the HDA temperature check point

6.4.2Relative humidity

The values below assume that no condensation on the drive occurs.

a.Operating

5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.

b.Non-operating

5% to 95% non-condensing relative humidity.

Savvio 15K SAS Product Manual, Rev. B

29

Image 37
Contents 100407739 Rev. B Savvio 15K SASPage Revision status summary sheet Savvio 15K SAS Product Manual, Rev. B Contents Installation Defect and error managementSeagate Technology support services Interface requirementsList of Figures Page Scope Savvio 15K SAS Product Manual, Rev. B Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean MICEuropean Union Restriction of Hazardous Substances RoHS Reference documentsSavvio 15K SAS Product Manual, Rev. B General description Media description Standard featuresPerformance Reliability Factory-installed accessoriesFormatted capacities Programmable drive capacityOptions Internal drive characteristics Performance characteristicsSeek performance characteristics Access time Gen 2.0 LP dataGeneral performance characteristics Format command execution timePrefetch/multi-segmented cache control Start/stop timeCache operation Prefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0DhThermal monitor Parameter Code DescriptionDST failure definition State of the drive prior to testingImplementation Invoking DSTShort test Function Code 001b Product warrantyExtended test Function Code 010b Log page entriesProduct repair and return information ShippingSavvio 15K SAS Product Manual, Rev. B AC power requirements Physical/electrical specificationsDC power requirements ST973451SS DC power requirementsGeneral DC power requirement notes ST936751SS DC power requirementsConducted noise immunity Power sequencingCurrent profiles Typical ST936751SS current profile ST973451SS in 3 Gbit operation Power dissipationST973451SS in 1.5 Gbit operation ST936751SS in 1.5 Gbit operation ST936751SS in 3 Gbit operationEnvironmental limits TemperatureRelative humidity Shock and vibration Effective altitude sea levelShock Recommended mounting Vibration Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingSavvio 15K SAS Product Manual, Rev. B Interface requirements SAS featuresDual port support Commands supported by Savvio SAS family drive Scsi commands supportedCommands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Inquiry data Mode Sense dataSavvio inquiry data Page Mode Data Header 04 45 dc cc 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsSAS transmitters and receivers SAS pin descriptionsSignal characteristics Eye masks Eye masks overview General interface characteristicsReceive eye mask Z1 OP Jitter tolerance masksPeak-to Transmitter signal characteristicsSinusoidal JitterReceiver signal characteristics Receiver jitter tolerance Maximum allowable jitterCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1 Impedance specificationsImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Savvio 15K SAS Product Manual, Rev. B Internet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling