Seagate ST973451SS, ST936751SS manual Vibration, Air cleanliness, Corrosive environment

Page 40

6.4.4.2Vibration

a. Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding

10-500 Hz @ 1.0 G (zero to peak)

Vibration may be applied in the X, Y, or Z axis.

Operating normal translational random flat profile

10 - 400 Hz

0.4 GRMS

b.Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:

15 minutes of duration at major resonant frequency 10-500 Hz @ 1.5 G (X, Y, or Z axis)

Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

10 - 500 Hz

1.2 GRMS

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding:

5-22 Hz @ 0.040 inches (1.02 mm) displacement (zero to peak)

20-500 Hz @ 3.0 G (zero to peak)

Vibration may be applied in the X, Y, or Z axis.

Non-operating translational random flat profile

10 - 500 Hz

1.2 GRMS

6.4.5Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

6.4.6Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds sshould be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

32

Savvio 15K SAS Product Manual, Rev. B

Image 40
Contents Savvio 15K SAS 100407739 Rev. BPage Revision status summary sheet Savvio 15K SAS Product Manual, Rev. B Contents Defect and error management InstallationSeagate Technology support services Interface requirementsList of Figures Page Scope Savvio 15K SAS Product Manual, Rev. B Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean MICReference documents European Union Restriction of Hazardous Substances RoHSSavvio 15K SAS Product Manual, Rev. B General description Media description Standard featuresPerformance Factory-installed accessories ReliabilityFormatted capacities Programmable drive capacityOptions Performance characteristics Internal drive characteristicsSeek performance characteristics Access time Gen 2.0 LP dataFormat command execution time General performance characteristicsPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operationReliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor Parameter Code DescriptionState of the drive prior to testing DST failure definitionImplementation Invoking DSTProduct warranty Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product repair and return informationSavvio 15K SAS Product Manual, Rev. B Physical/electrical specifications AC power requirementsDC power requirements ST973451SS DC power requirementsST936751SS DC power requirements General DC power requirement notesConducted noise immunity Power sequencingCurrent profiles Typical ST936751SS current profile ST973451SS in 3 Gbit operation Power dissipationST973451SS in 1.5 Gbit operation ST936751SS in 3 Gbit operation ST936751SS in 1.5 Gbit operationEnvironmental limits TemperatureRelative humidity Shock and vibration Effective altitude sea levelShock Recommended mounting Vibration Air cleanlinessCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSavvio 15K SAS Product Manual, Rev. B SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Savvio SAS family driveCommands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Inquiry data Mode Sense dataSavvio inquiry data Page Mode Data Header 04 45 dc cc 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Physical characteristics Connector requirementsElectrical description Pin descriptionsSAS pin descriptions SAS transmitters and receiversSignal characteristics Eye masks Eye masks overview General interface characteristicsReceive eye mask Jitter tolerance masks Z1 OPTransmitter signal characteristics Peak-toSinusoidal JitterReceiver signal characteristics Receiver jitter tolerance Maximum allowable jitterCompliant jitter test pattern Cjtpat Impedance specifications Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Savvio 15K SAS Product Manual, Rev. B Seagate Technology support services InternetPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index NumericsPage SAS See also cooling