Seagate Official Manual for Reliable Computer Drives - ST2000NM0043 and Other Models

Page 23

6.1.3Seek errors

A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks. Unrecoverable seek errors (Sense Key = 04h) are classified as drive failures.

6.1.4Interface errors

An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss of word sync, or CRC error.

6.2Reliability and service

You can enhance the reliability of Constellation ES disc drives by ensuring that the drive receives adequate cooling. Section 7.0 provides temperature measurements and other information that may be used to enhance the service life of the drive. Section 11.2 provides recommended air-flow information.

6.2.1Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)

The production disc drive shall achieve an AFR of 0.73% (MTBF of 1,200,000 hours) when operated in an environment that ensures the HDA case temperatures do not exceed the values specified in Section 7.5. Oper- ation at case temperatures outside the specifications in Section 7.5 may increase the product AFR (decrease the MTBF). The AFR (MTBF) is a population statistic not relevant to individual units.

The AFR (MTBF) specification is based on the following assumptions for Enterprise Storage System environ- ments:

8,760 power-on hours per year.

250 average on/off cycles per year.

Operations at nominal voltages.

Systems will provide adequate cooling to ensure the case temperatures specified in Section 7.5 are not exceeded. Temperatures outside the specifications in Section 7.5 will increase the product AFR and decrease the MTBF.

6.2.2Preventive maintenance

No routine scheduled preventive maintenance is required.

6.2.3Hot plugging the drive

When a disc is powered on by switching the power or hot plugged, the drive runs a self test before attempting to communicate on its’ interfaces. When the self test completes successfully, the drive initiates a Link Reset starting with OOB. An attached device should respond to the link reset. If the link reset attempt fails, or any time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming both ports are out of sync.

If the self-test fails, the drive does not respond to link reset on the failing port.

Note. It is the responsibility of the systems integrator to assure that no temperature, energy, voltage haz- ard, or ESD potential hazard is presented during the hot connect/disconnect operation. Discharge the static electricity from the drive carrier prior to inserting it into the system.

Constellation ES Series SAS Product Manual, Rev. F

15

Image 23
Contents SED Fips 140-2 Models ST32000446SS ST31000426SS ST3500416SSStandard Models Self-Encrypting Drive Models Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPower Constellation ES Series SAS Product Manual, Rev. F List of Figures Constellation ES Series SAS Product Manual, Rev. F Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping PowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsRegulation ±5% Constellation ES Series SAS Product Manual, Rev. F +5V Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. F GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation Os per Second ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GB500GB models in 3Gb operation 500GB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normalCorrosive environment Air cleanlinessAcoustics Mounting configuration dimensions Mechanical specificationsLevel 2 security About FipsPurpose Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation ES inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsConstellation ES Series SAS Product Manual, Rev. F Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. F Page Seagate Technology LLC

ST4000NM0053, ST4000NM0023, ST32000444SSIM, ST32000646NS, ST3000NM0063 specifications

Seagate is a prominent name in the storage industry, renowned for its high-performance hard disk drives (HDDs). Among its popular enterprise offerings are models like the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, which cater to various data center and server needs.

The Seagate ST2000NM0043 is a 2TB 7200 RPM SATA drive designed for high availability and performance in enterprise environments. It features a 128MB cache, ensuring efficient data transfer speeds and quick access to frequently used data. This model boasts a mean time between failures (MTBF) of 1.4 million hours, emphasizing its reliability for continuous operation in demanding applications.

The ST32000645NS, offering 2TB of storage and a 7200 RPM spindle speed, is ideal for environments where large amounts of data need to be stored and accessed quickly. It supports SAS interfaces, providing enhanced data integrity and improved system performance. With its aggressive power management features, this model strikes a balance between performance and energy efficiency, making it suitable for both traditional data centers and cloud applications.

The ST3000NM0043 stands out with a capacity of 3TB, further addressing the growing need for more substantial storage solutions. Like its counterparts, it operates at 7200 RPM and is equipped with advanced caching mechanisms that help enhance overall performance. Its high durability and enterprise-grade features make it a preferred choice for storage-intensive applications.

The ST2000NM0033 focuses on delivering storage solutions for environments needing both capacity and reliability. With its 2TB capacity and 7200 RPM rotation speed, it provides an effective solution for businesses looking to balance workload and storage needs without compromising performance. This model also features Seagate's advanced technology that optimizes workflow and minimizes latency.

Lastly, the ST2000NM0023 mirrors many of the features found in its siblings, offering a 2TB capacity and optimized for high reliability and performance. With Seagate's commitment to innovating in the HDD space, features such as self-monitoring, analysis, and reporting technology (SMART) help maintain the drive's health and prevent potential failures.

In conclusion, Seagate's range of HDDs, exemplified by the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, reflects a dedication to providing robust, high-capacity storage solutions. Their advanced technologies, reliability ratings, and performance features make them ideal choices for enterprise environments demanding efficiency and durability.