Seagate ST3000NM0063, ST1000NM0063, ST1000NM0043, ST2000NM0033, ST2000NM0023, ST2000NM0043 manual

Page 67

Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage.

When power is applied to the drive, it takes saved values from the media and stores them as current val- ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a “Check Condition” status.

On drives requiring unique saved values, the required unique saved values are stored into the saved val- ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with unique default values also.

On standard OEM drives, the saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping.

3.Current values

Current values are volatile values being used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.

4.Changeable values

Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values and saved values can be changed by a Mode Select command. A one (1) indicates the value can be changed. A zero (0) indicates the value is not changeable. For example, in Table 10, refer to Mode page 81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page 81. Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of these bits are changeable.

The changeable values list can only be changed by downloading new firmware into the flash E-PROM.

Note. Because there are often several different versions of drive control firmware in the total population of drives in the field, the Mode Sense values given in the following tables may not exactly match those of some drives.

The following tables list the values of the data bytes returned by the drive in response to the Mode Sense com- mand pages for SCSI implementation (see the SAS Interface Manual).

DEF = Default value. Standard OEM drives are shipped configured this way.

CHG = Changeable bits; indicates if default value is changeable.

Constellation ES Series SAS Product Manual, Rev. F

59

Image 67
Contents Standard Models Self-Encrypting Drive Models ST32000446SS ST31000426SS ST3500416SSSED Fips 140-2 Models Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPower Constellation ES Series SAS Product Manual, Rev. F List of Figures Constellation ES Series SAS Product Manual, Rev. F Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsRegulation ±5% Constellation ES Series SAS Product Manual, Rev. F +5V Power sequencing General DC power requirement notesConducted noise immunity TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. F GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GBOs per Second 500GB models in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Vibration a. Operating-normalAcoustics Air cleanlinessCorrosive environment Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsConstellation ES Series SAS Product Manual, Rev. F Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. F Page Seagate Technology LLC

ST4000NM0053, ST4000NM0023, ST32000444SSIM, ST32000646NS, ST3000NM0063 specifications

Seagate is a prominent name in the storage industry, renowned for its high-performance hard disk drives (HDDs). Among its popular enterprise offerings are models like the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, which cater to various data center and server needs.

The Seagate ST2000NM0043 is a 2TB 7200 RPM SATA drive designed for high availability and performance in enterprise environments. It features a 128MB cache, ensuring efficient data transfer speeds and quick access to frequently used data. This model boasts a mean time between failures (MTBF) of 1.4 million hours, emphasizing its reliability for continuous operation in demanding applications.

The ST32000645NS, offering 2TB of storage and a 7200 RPM spindle speed, is ideal for environments where large amounts of data need to be stored and accessed quickly. It supports SAS interfaces, providing enhanced data integrity and improved system performance. With its aggressive power management features, this model strikes a balance between performance and energy efficiency, making it suitable for both traditional data centers and cloud applications.

The ST3000NM0043 stands out with a capacity of 3TB, further addressing the growing need for more substantial storage solutions. Like its counterparts, it operates at 7200 RPM and is equipped with advanced caching mechanisms that help enhance overall performance. Its high durability and enterprise-grade features make it a preferred choice for storage-intensive applications.

The ST2000NM0033 focuses on delivering storage solutions for environments needing both capacity and reliability. With its 2TB capacity and 7200 RPM rotation speed, it provides an effective solution for businesses looking to balance workload and storage needs without compromising performance. This model also features Seagate's advanced technology that optimizes workflow and minimizes latency.

Lastly, the ST2000NM0023 mirrors many of the features found in its siblings, offering a 2TB capacity and optimized for high reliability and performance. With Seagate's commitment to innovating in the HDD space, features such as self-monitoring, analysis, and reporting technology (SMART) help maintain the drive's health and prevent potential failures.

In conclusion, Seagate's range of HDDs, exemplified by the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, reflects a dedication to providing robust, high-capacity storage solutions. Their advanced technologies, reliability ratings, and performance features make them ideal choices for enterprise environments demanding efficiency and durability.