Seagate ST4000NM0053 Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 76

12.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 19. The receiver is AC cou- pling to eliminate ground shift noise.

 

TX

Transmitter

Differential

Transfer Medium

100

 

 

TY

Figure 19. SAS transmitters and receivers

.01

.01

RX

Receiver

100

RY

12.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

12.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 15 for signal type and signal name information.

12.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 16.

Table 16: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

 

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

Format in progress, each cylinder change

 

Toggles on/off

 

 

 

 

68

Constellation ES Series SAS Product Manual, Rev. F

Image 76
Contents Standard Models Self-Encrypting Drive Models ST32000446SS ST31000426SS ST3500416SSSED Fips 140-2 Models Revision history Contents Defect and error management InstallationAbout Fips About self-encrypting drives Interface requirementsPower Constellation ES Series SAS Product Manual, Rev. F List of Figures Constellation ES Series SAS Product Manual, Rev. F Seagate Technology support services Seagate Online Support and ServicesScope Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionPerformance ReliabilityFormatted capacities Programmable drive capacityFactory-installed options Performance characteristics Internal drive characteristicsSeek performance characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationReliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Seek errorsInterface errors Preventive maintenance4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor State of the drive prior to testing Drive Self Test DSTDST failure definition ImplementationShort and extended tests Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes AC power requirements DC power requirementsRegulation ±5% Constellation ES Series SAS Product Manual, Rev. F +5V Power sequencing General DC power requirement notesConducted noise immunity Current profiles TB model current profilesConstellation ES Series SAS Product Manual, Rev. F GB model current profiles Power dissipation 2TB models in 3Gb operation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GBOs per Second 500GB models in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Vibration a. Operating-normal Recommended mountingAcoustics Air cleanlinessCorrosive environment Mechanical specifications Mounting configuration dimensionsPurpose About FipsLevel 2 security Controlled access Admin SPAbout self-encrypting drives Data encryptionDefault password Random number generator RNGDrive locking Data bandsAuthenticated firmware download Power requirementsSupported commands Cryptographic eraseDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Physical characteristics Connector requirementsElectrical description Pin descriptionsSignal characteristics PowerSAS transmitters and receivers Ready LED OutSAS-2 Specification Compliance LED drive signalDifferential signals General interface characteristicsConstellation ES Series SAS Product Manual, Rev. F Index NumericsKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. F Page Seagate Technology LLC

ST4000NM0053, ST4000NM0023, ST32000444SSIM, ST32000646NS, ST3000NM0063 specifications

Seagate is a prominent name in the storage industry, renowned for its high-performance hard disk drives (HDDs). Among its popular enterprise offerings are models like the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, which cater to various data center and server needs.

The Seagate ST2000NM0043 is a 2TB 7200 RPM SATA drive designed for high availability and performance in enterprise environments. It features a 128MB cache, ensuring efficient data transfer speeds and quick access to frequently used data. This model boasts a mean time between failures (MTBF) of 1.4 million hours, emphasizing its reliability for continuous operation in demanding applications.

The ST32000645NS, offering 2TB of storage and a 7200 RPM spindle speed, is ideal for environments where large amounts of data need to be stored and accessed quickly. It supports SAS interfaces, providing enhanced data integrity and improved system performance. With its aggressive power management features, this model strikes a balance between performance and energy efficiency, making it suitable for both traditional data centers and cloud applications.

The ST3000NM0043 stands out with a capacity of 3TB, further addressing the growing need for more substantial storage solutions. Like its counterparts, it operates at 7200 RPM and is equipped with advanced caching mechanisms that help enhance overall performance. Its high durability and enterprise-grade features make it a preferred choice for storage-intensive applications.

The ST2000NM0033 focuses on delivering storage solutions for environments needing both capacity and reliability. With its 2TB capacity and 7200 RPM rotation speed, it provides an effective solution for businesses looking to balance workload and storage needs without compromising performance. This model also features Seagate's advanced technology that optimizes workflow and minimizes latency.

Lastly, the ST2000NM0023 mirrors many of the features found in its siblings, offering a 2TB capacity and optimized for high reliability and performance. With Seagate's commitment to innovating in the HDD space, features such as self-monitoring, analysis, and reporting technology (SMART) help maintain the drive's health and prevent potential failures.

In conclusion, Seagate's range of HDDs, exemplified by the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, reflects a dedication to providing robust, high-capacity storage solutions. Their advanced technologies, reliability ratings, and performance features make them ideal choices for enterprise environments demanding efficiency and durability.