Seagate ST4000NM0033, ST1000NM0063, ST1000NM0043, ST2000NM0033 manual Installation, Drive orientation

Page 57

11.0Installation

Constellation ES disc drive installation is a plug-and-play process. There are no jumpers, switches, or termina- tors on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend the use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 12.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 14. Physical interface

11.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

Constellation ES Series SAS Product Manual, Rev. F

49

Page 56 Page 58
Image 57
Page 56 Page 58
Contents ST32000446SS ST31000426SS ST3500416SS Standard Models Self-Encrypting Drive ModelsSED Fips 140-2 Models Revision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPower Constellation ES Series SAS Product Manual, Rev. F List of Figures Constellation ES Series SAS Product Manual, Rev. F Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes DC power requirements AC power requirementsRegulation ±5% Constellation ES Series SAS Product Manual, Rev. F +5V General DC power requirement notes Power sequencingConducted noise immunity TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. F GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GB 500GB models in 3Gb operationOs per Second 500GB models in 6Gb operation Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Recommended mounting Vibration a. Operating-normalAir cleanliness AcousticsCorrosive environment Mounting configuration dimensions Mechanical specificationsAbout Fips PurposeLevel 2 security Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsConstellation ES Series SAS Product Manual, Rev. F Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. F Page Seagate Technology LLC

ST4000NM0053, ST4000NM0023, ST32000444SSIM, ST32000646NS, ST3000NM0063 specifications

Seagate is a prominent name in the storage industry, renowned for its high-performance hard disk drives (HDDs). Among its popular enterprise offerings are models like the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, which cater to various data center and server needs.

The Seagate ST2000NM0043 is a 2TB 7200 RPM SATA drive designed for high availability and performance in enterprise environments. It features a 128MB cache, ensuring efficient data transfer speeds and quick access to frequently used data. This model boasts a mean time between failures (MTBF) of 1.4 million hours, emphasizing its reliability for continuous operation in demanding applications.

The ST32000645NS, offering 2TB of storage and a 7200 RPM spindle speed, is ideal for environments where large amounts of data need to be stored and accessed quickly. It supports SAS interfaces, providing enhanced data integrity and improved system performance. With its aggressive power management features, this model strikes a balance between performance and energy efficiency, making it suitable for both traditional data centers and cloud applications.

The ST3000NM0043 stands out with a capacity of 3TB, further addressing the growing need for more substantial storage solutions. Like its counterparts, it operates at 7200 RPM and is equipped with advanced caching mechanisms that help enhance overall performance. Its high durability and enterprise-grade features make it a preferred choice for storage-intensive applications.

The ST2000NM0033 focuses on delivering storage solutions for environments needing both capacity and reliability. With its 2TB capacity and 7200 RPM rotation speed, it provides an effective solution for businesses looking to balance workload and storage needs without compromising performance. This model also features Seagate's advanced technology that optimizes workflow and minimizes latency.

Lastly, the ST2000NM0023 mirrors many of the features found in its siblings, offering a 2TB capacity and optimized for high reliability and performance. With Seagate's commitment to innovating in the HDD space, features such as self-monitoring, analysis, and reporting technology (SMART) help maintain the drive's health and prevent potential failures.

In conclusion, Seagate's range of HDDs, exemplified by the ST2000NM0043, ST32000645NS, ST3000NM0043, ST2000NM0033, and ST2000NM0023, reflects a dedication to providing robust, high-capacity storage solutions. Their advanced technologies, reliability ratings, and performance features make them ideal choices for enterprise environments demanding efficiency and durability.
Top Page Image Contents