Seagate ST9146652SS, ST973452SS, ST973352SS, ST973252SS, ST9146752SS manual Drive mounting, Grounding

Page 53

11.3Drive mounting

Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.

The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiffness:

K x X = F < 15lb = 67N

where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

11.4Grounding

Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electri- cally isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mount- ing the drive in the host equipment.

Increased radiated emissions may result if you do not provide the maximum surface area ground connection between system ground and drive ground. This is the system designer’s and integrator’s responsibility.

Savvio 15K.2 SAS Product Manual, Rev. E

45

Image 53
Contents ST9146652SS ST973252SS ST9146852SSST9146752SS ST973452SSST973352SSStandard Models Self-Encrypting Drive Models SED Fips 140-2 ModelsPage Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Savvio 15K.2 SAS Product Manual, Rev. E List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean MICEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresFormatted capacities PerformanceReliability Options Programmable drive capacityInternal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time Format command execution timeGeneral performance characteristics Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesProduct repair and return information Product warrantyShipping DC power requirements Physical/electrical specificationsAC power requirements Gbit mode Amps 146GB models DC power requirements73GB models DC power requirements Conducted noise immunity General DC power requirement notesPower sequencing Current profile for 146GB models Current profilesCurrent profile for 73GB models 146GB models in 3.0 Gbit operation Power dissipation146GB models in 6.0 Gbit operation 73GB models in 3.0 Gbit operation 73GB models in 6.0 Gbit operationRelative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal Acoustics Dimensions Mechanical specificationsLevel 2 security About FipsPurpose Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Savvio inquiry data Mode Sense dataInquiry data Page Mode Data Header 00 00 05 12 8B 00 10 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsSAS transmitters and receivers SAS pin descriptionsSignal characteristics Additional information SAS-2 Specification complianceGeneral interface characteristics Savvio 15K.2 SAS Product Manual, Rev. E Numerics IndexIraw Msid Mtbf See also cooling