Seagate ST9250310AS, ST9640320AS manual Reliability, Agency certification, Safety certification

Page 22

3.13

Reliability

 

 

 

Measurement type

Specification

 

 

Nonrecoverable read errors

1 per 1014 bits read, max.

Annualized Failure Rate (AFR)

<0.48%

 

 

Load/Unload (U/UL)

 

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

 

 

50,000 hard power on/off cycles

32°C, 80% relative humidity

600,000 software-controlled power on/off cycles

5°C, 80% relative humidity

50,000 hard power on/off cycles

5°C, 10% relative humidity

 

55°C, 16% relative humidity

 

Warranty

 

To determine the warranty for a specific drive, use a web browser to access the

 

 

following web page:

 

 

http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance

 

 

You will be asked to provide the drive serial number, model number (or part number)

 

 

and country of purchase. After submitting this information, the system will display the

 

 

warranty information for your drive.

3.14Agency certification

3.14.1Safety certification

These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.

3.14.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

16

Momentus Product Manual, Rev. D

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Momentus Revision history Revision DateContents Momentus Product Manual, Rev. D List of Figures Page Seagate Technology support services Seagate Online Support and Services4K byte/sector models IntroductionByte/sector models About the Serial ATA interface Specification summary table Drive specificationsDrive specifications for 640, 500 and 400GB models To 12,192 m -1000 ft to 40,000 ft Drive specifications for 320, 250 and 160GB models Drive specifications for 320, 250 and 160GB models Formatted capacity Default logical geometryLBA mode Physical organizationSeek time Physical characteristicsRecording and interface technology Typical seek timesPower specifications Start/stop timesConducted noise Typical current profileDeferred spinup Voltage toleranceActive mode Power-management modesPower management modes Idle modeEnvironmental specifications Nonoperating shock ShockOperating shock VibrationElectromagnetic immunity Drive A-weighted Sound Power Levels SWL, BAAcoustics Test for Prominent Discrete Tones PDTsReliability Safety certificationMeasurement type Specification Agency certificationAustralian C-Tick N176 Korean RRLFCC verification European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment China Restriction of Hazardous Substances RoHS DirectiveConfiguring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsDrive mounting Top cover stiffness/deflectionMeasurements shown in are in inches Serial ATA Sata interface Serial ATA connector pin definitionsSignal Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedSupported ATA commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard security commandsIdentify Device command Word Description ValueXx07H Description if bit is set to Bit Set Features command Set Features command valuesM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Momentus Product Manual, Rev. D Index Page Page Momentus Product Manual, Rev. D Page Seagate Technology LLC
Top Page Image Contents