Seagate ST9320312AS, ST9640320AS 3 S.M.A.R.T. commands, Code in features register A.R.T. command

Page 37

5.3.3S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni- tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-8 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that elimi- nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 10: S.M.A.R.T. commands

Code in features register

S.M.A.R.T. command

 

 

D0H

S.M.A.R.T. Read Data

D1H

Vendor-specific

D2H

S.M.A.R.T. Enable/Disable Attribute Autosave

D3H

S.M.A.R.T. Save Attribute Values

D4H

S.M.A.R.T. Execute Off-line Immediate (runs DST)

D5H

S.M.A.R.T. Read Log Sector

D6H

S.M.A.R.T. Write Log Sector

D7H

Vendor-specific

D8H

S.M.A.R.T. Enable Operations

D9H

S.M.A.R.T. Disable Operations

DAH

S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

Momentus Product Manual, Rev. D

31

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Momentus Revision Date Revision historyContents Momentus Product Manual, Rev. D List of Figures Page Seagate Online Support and Services Seagate Technology support services4K byte/sector models IntroductionByte/sector models About the Serial ATA interface Specification summary table Drive specificationsDrive specifications for 640, 500 and 400GB models To 12,192 m -1000 ft to 40,000 ft Drive specifications for 320, 250 and 160GB models Drive specifications for 320, 250 and 160GB models LBA mode Default logical geometryFormatted capacity Physical organizationRecording and interface technology Physical characteristicsSeek time Typical seek timesStart/stop times Power specificationsDeferred spinup Typical current profileConducted noise Voltage tolerancePower management modes Power-management modesActive mode Idle modeEnvironmental specifications Operating shock ShockNonoperating shock VibrationAcoustics Drive A-weighted Sound Power Levels SWL, BAElectromagnetic immunity Test for Prominent Discrete Tones PDTsMeasurement type Specification Safety certificationReliability Agency certificationAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS China Restriction of Hazardous Substances RoHS DirectiveHandling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveTop cover stiffness/deflection Drive mountingMeasurements shown in are in inches Signal Serial ATA connector pin definitionsSerial ATA Sata interface Segment Pin Function DefinitionP10 Ground 2nd mate P11 Reserved Pin Function DefinitionCommand name Command code in hex ATA-standard commands Supported ATA commandsATA-standard security commands Command name Command code in hexWord Description Value Identify Device commandXx07H Description if bit is set to Bit Set Features command values Set Features commandM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Momentus Product Manual, Rev. D Index Page Page Momentus Product Manual, Rev. D Page Seagate Technology LLC
Top Page Image Contents