Seagate ST150176LW/LC manual Delay Motor Start and Motor Start options

Page 35

Barracuda 50 Installation Guide, Rev. A

33

3.Check the other available jumper settings (optional) This drive provides several features for unique configura- tions. You will not normally need to change from the default settings for normal operation. See Figure 13 on page 34.

Single-ended mode option

You can force the drive to operate only in SE mode by installing a jumper on J2 pins 15 and 16. The default is to allow the drive to automatically detect and use SE or LVD mode. See page 11 for a description of these two modes.

Delay Motor Start and Motor Start options

You can control when the drive’s motor starts spinning the media using these two jumper positions (J2 pins 11 and 12 and J2 pins 13 and 14). You can configure the drive to delay spinning up until a certain number of seconds elapse or until the drive receives a Start Unit command from the host sys- tem. The default settings are with both off so that the drive begins spining up as soon as it receives power.

Write Protect option

You can install a jumper connecting J2 pins 9 and 10 to pre- vent anyone from writing data to this disc drive (users can still read data from the drive). This jumper is normally left off to allow users to write data to the drive.

Parity Check option

You can disable parity checking by installing a jumpers on J2 pins 7 and 8. Most systems prefer that parity checking remain enabled. Refer to your host adapter or system docu- mentation to determine whether your host adapter supports parity checking.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Barracuda Disc Drive Contents Preface Electrostatic discharge protection Handling precautionsImportant safety information and precautions Barracuda 50 Installation Guide, Rev. a Wichtige Sicherheitshinweise Barracuda 50 Installation Guide, Rev. a Barracuda 50 Installation Guide, Rev. a Electromagnetic compliance Regulatory agency complianceElectromagnetic susceptibility Australian C-Tick Electromagnetic compliance for the European UnionGeneral description Primary benefits of LVD technology Single-ended and low voltage differential modesProviding adequate cooling SE and LVD bus configurationsData bus widths Kühlung des Systems Suggested air flow Characteristics ST150176LW/LC +12 Set the Scsi ID on the drive ST150176LW installationSetting the Scsi ID on ST150176LW drives Configure termination Scsi bus termination Setting terminator power jumpers Configure termination powerConnect the drive activity remote LED optional Drive Active LED indicator connectionsParity Check option Delay Motor Start and Motor Start optionsWrite Protect option Additional jumper options Format the drive Mount the drive in the host system and connect cablingConnecting cables to the drive Multiple-drive connection to host adapter Mounting configuration dimensions LW model Alternate Scsi ID select and LED connection Additional connector on ST150176LW drivesScsi ID ST150176LC installationSetting the Scsi ID on ST150176LC drives Configure termination Delay Motor Start and Motor Start options Additional jumper options Pin I/O connection to drive LC model Mount the drive in the host systemMounting configuration dimensions LC model Important information about formatting the drive System preparation DOS, Windows 3.1, Windows 95, and WindowsDrive formatting Macintosh Seagate Technology support services Presales Support Customer Service CSO European Support Services Africa/Middle East Support Services SeaFAX Page Page

ST150176LW/LC specifications

The Seagate ST150176LW/LC is a high-capacity hard disk drive that exemplifies reliability and performance in data storage technology. Designed primarily for enterprise environments, this drive offers a robust solution for businesses requiring efficient data management, backup, and storage solutions.

One of the standout features of the Seagate ST150176LW/LC is its impressive capacity of 1.5TB. This substantial storage allows for the management of large volumes of data, making it ideal for organizations that handle extensive databases, multimedia files, and other data-intensive applications. The drive is equipped with a 7200 RPM spindle speed, ensuring rapid data access and faster read/write operations, which is critical for maintaining high performance in data-intensive workflows.

The ST150176LW/LC incorporates Advanced Format Technology, which optimizes the sector size to increase data accuracy and storage efficiency. This technology enables better alignment of data structures on the magnetic media, contributing to enhanced performance and capacity utilization. Additionally, the drive is designed with a SATA interface that supports data transfer rates of up to 6 Gbps, allowing seamless integration with modern systems.

Reliability is a cornerstone of the Seagate ST150176LW/LC drive’s design. It features enhanced integrity technologies, ensuring protection against data corruption and hardware errors. The drive also supports error correction algorithms that proactively address potential issues, leading to reduced downtime and improved data integrity for mission-critical applications. With an MTBF (Mean Time Between Failures) rating that underscores its durability, it is well-suited for continuous operation in demanding environments.

Furthermore, the ST150176LW/LC is built with power efficiency in mind, featuring optimized power management features that contribute to lower energy consumption. This not only helps in reducing operational costs but also aligns with the growing push towards sustainability in data management practices.

In summary, the Seagate ST150176LW/LC hard disk drive combines high capacity, exceptional performance, and reliable data integrity in a single device, making it a preferred choice for enterprises looking to enhance their data storage capabilities. Its advanced technologies and robust characteristics drive efficiency and provide businesses with the dependable storage solutions they require.
Top Page Image Contents