Seagate ST3500414CS Serial ATA device plug connector pin definitions, Pin Function Definition

Page 32

4.2Serial ATA device plug connector pin definitions

Table 7 summarizes the signals on the Serial ATA interface and power connectors.

Table 7:	Serial ATA connector pin definitions

Segment	Pin	Function	Definition

	S1	Ground	2nd mate

	S2	A+	Differential signal pair A from Phy

	S3	A-

	S4	Ground	2nd mate

	S5	B-	Differential signal pair B from Phy

	S6	B+
Signal
Signal	S7	Ground	2nd mate

		Key and spacing separate signal and power segments

	P1	V33	3.3V power
	P2	V33	3.3V power
	P3	V33	3.3V power, pre-charge, 2nd mate
	P4	Ground	1st mate

	P5	Ground	2nd mate

	P6	Ground	2nd mate

	P7	V5	5V power, pre-charge, 2nd mate
Power	P8	V5	5V power
	P9	V5	5V power
	P10	Ground	2nd mate

	P11	Ground or LED signal	If grounded, drive does not use deferred spin

	P12	Ground	1st mate.

	P13	V12	12V power, pre-charge, 2nd mate
	P14	V12	12V power
	P15	V12	12V power

Notes:

1.All pins are in a single row, with a 1.27mm (0.050 in) pitch.

2.The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are:

•the ground pins P4 and P12.

•the pre-charge power pins and the other ground pins.

•the signal pins and the rest of the power pins.

3.There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.

4.All used voltage pins (Vx) must be terminated.

26	Video 3.5 HDD Product Manual, Rev. J

Image 32

Contents Video 3.5 HDD Revision history Revision Date Sheets affected or commentsPipeline HD.2 Series Sata Product Manual, Rev. J Pipeline HD.2 Series Sata Product Manual, Rev. J Contents Pipeline HD.2 Series Sata Product Manual, Rev. J Introduction About the Serial ATA interface Drive specifications Specification summary tablesDrive specifications summary for 1000GB models Drive specification ST31000424CS ST31000322CSVideo 3.5 HDD Product Manual, Rev. J Drive specifications summary for 500 and 320GB models Video 3.5 HDD Product Manual, Rev. J Drive specifications summary for 250 and 160GB models Drive specification ST3250412CS ST3250312CS ST3160316CSVideo 3.5 HDD Product Manual, Rev. J Default logical geometry LBA modeFormatted capacity Recording and interface technologyStart/stop times Physical characteristicsSeek time Power specifications Voltage tolerance Typical current profilesConducted noise Power management modes Active modeIdle mode Sleep modeEnvironmental specifications Shock Operating shockNon-operating shock VibrationDrive A-weighted Sound Power Levels SWL, BA Acoustics emissionsElectromagnetic immunity Test for Prominent Discrete Tones PDTsSafety certification ReliabilityAgency certification Annualized Failure Rate AFRFCC verification Korean RRLAustralian C-Tick N176 China Restriction of Hazardous Substances RoHS Directive Environmental protectionCorrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions for 1000GB models Drive mountingMounting dimensions for 500, 320, 250 and 160GB models Serial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionCommand name Command code in hex Supported ATA commandsSupported ATA commands F3H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordIdle Immediate command with Iunload faeture is supported Set Features command Set Features command valuesCode in features register A.R.T. command 3 S.M.A.R.T. commandsM.A.R.T. commands Seagate Technology support services Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index RRL Page Video 3.5 HDD Product Manual, Rev. J Page Seagate Technology LLC

Related manuals

Manual 50 pages 5.86 Kb